Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A 50 Hz, 440 V, 3-phase , 4-pole induction motor develops half the rated torque at 1490 r.p.m. with the applied voltage magnitude remaining at the rated value, what should be its frequency if the motor has to develop the same torque at 1550 r.p.m.? Neglect stator resistance, leakage reactance and iron losses.
(a) determine the contact resistor that can go on the base if the length of the contact is 10 * Wb. (b) Plot the change in conductance in relation to varying the doping from 1014/cm3 to 1018/cm3 at room temperature. Redo the graph at 77K;
When the input returns 1the sequence stops were it was left off. The output should change only on a rising clock edge. Make 000 the initial state. Assume an implicit rising clock is ANDed with every FSM transition condition.
Carlos runs with velocity v=(5.0 m/s, 25 degrees north of east) for 10 min. How far north of his starting position does Carlos finish
A system has the following input/output relation: y(n) = x(n) + .5 y(n -1). If the input x(n) is the sinusoidal signal shown in problem 1.32(d) (Above), the steady-state output will have the following form: y(n) = A sin(Bn+C). Determine the value ..
The two input terminals of an op-amp are connected to two wires leading from the output terminals of a transducer, which carries a sinusoidal output signal of 20 mV amplitude and 500Hz frequency.
Design an active loaded CS amplifier to obtain a voltage gain of 30V/V. The output load is a 10 fF capacitor. Use 0.25u CMOS technology. Calculate it's high frequency 3 dB value, fH, given that Cgs = 5 fF, Cgd = 0.5fF, and signal source resistance..
Design a one-op-ampactive band pass filter that has a midband (at 5 KHz) inputimpedance of approximately 10K, a midband gain of approximately 1and a frequency response from 1 to 10KHz(corner frequencies).Verify by computing the circuit frequency r..
what do u mean by term slip of three phase induction motor calculate the slip of 4-pole induction motor running at 1470 rpm while bieng connected to a 50 hz three phase source
The IC differential amplifier is to be fabricated in a CMOS technology having the technology specifications of Kn' = 200 uA/V. Kp' = 100 uA/V. Vtn = 1V Vtp = -1V Va = 50V L = 1u. Calculate all the device widths for a constant bias current of 1mA
Determine the EA or offset, if applicable from the addressing modes(i) Immediate, (ii) Direct, (iii) Register using BX, (iv) registerindirect using BX, (v) Register relative using BX, (vi) Basedindexed, and (vii) Based indexed relative.
Two Si samples are doped n-type and p-type such that they have the same resistance. If the electron and hole mobilities are respectively 1350 and 450 cm2/Vs, find the relative values of Na and Nd.
In the case of a problem in the communication process in general (not just using Fieldbus), describe how you would troubleshoot a communications problem at the physical layer. Describe also the tools that you would use to troubleshoot the communic..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd