What reduction below atmospheric pressure must be achieved

Assignment Help Civil Engineering
Reference no: EM13320693

water at 150 degrees in a beaker is placed in an airtight chamber. Air is gradually pumped out of the container. What reduction below atmospheric pressure of 14.7 psi must be achieved before water boils?

Reference no: EM13320693

Questions Cloud

Determine what is the mass of the silver : A Kennedy half dollar has a mass of 1.150 X 10-2 Kg. The coins is a mixture of silver and cooper, and in water weights 0.1011 N. What is the mass of the silver
What is the rate of removal of thermal energy in watts : A copper cup of mass 0.300 kg contains 1.00 kg of water at 315 K. It is cooled so that the temperature decreases by 2.50 K each minute. What is the rate of removal of thermal energy in watts
What is the safety factor used if the structure was designed : Link BC is 6 mm thick, has a width w= 25 mm, and is made of a steel with a 480 MPa ultimate strength in tension. What is the safety factor used if the structure was designed to support a 16 kN load P
Determine is the final image real or virtual : Two converging lenses with focal lengths of f1 = 2.00 cm and f2 = 5.00 cm are situated 14.0 cm apart on a long optics bench. determine Is the final image real or virtual
What reduction below atmospheric pressure must be achieved : water at 150 degrees in a beaker is placed in an airtight chamber. Air is gradually pumped out of the container. What reduction below atmospheric pressure of 14.7 psi must be achieved before water boils
Constantly and rapidly changing : Identify examples in your experience demonstrating how the following factors currently influence managers: globalization, rapid change, innovation, diversity, and corporate ethics and values.
What must be the speed of a particle : A velocity selector has a magnetic field of magnitude 0.32 T perpendicular to an electric field of magnitude of 0.34 MV/m. What must be the speed of a particle for it to pass through undeflected
Determine what is the effluent concentration at the rate : A first order reaction occurs in a PFR at the rate of 2.1 hr^-1. The reactor volume is 1400L and flow is 15 gpm. If the influent concentration is 200 mg/L, then what is the effluent concentration
Example of a health care market : Choose an example of a health care market and identify ways in which it differs from perfectly competitive model. Do you think that these deviations from competition could each be repaid by appropriate policies? Discuss

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is partial pressure of each gass componet at 25 degrees

A 1-m^3 volume tank contains a mixture of 18.32 moles of oxygen, 16.40 moles of Nitrogen, and 6.15 moles of carbondioxide. What is the partial pressure of each gass componet at 25 degrees

  Determine the final density of the gas-carbon dioxide

Carbon dioxide at 30 C and 320 kPa absolute pressure expands isothermally to an absolute pressure of 170 kPa. Determine the final density of the gas.

  Determine the pressure at the point in n per m2 gage

Near the point (x, z) =(3,2) in a flow with a zero y-component (v=0), the velocity component are described by u =3x-3z, and w = 6-4z+ x. The velocities u and w are in m/s and are in the x- and z- directions, respectively.

  Determine the rate of entropy production within the turbine

Assuming the kinetic and potential energy effects to be negligible, determine D) the isentropic turbine efficiency E) the entropy at the exit of the turbine, in kJ/kg K F) the rate of entropy production within the turbine

  Determine the velocity and acceleration of block b

Determine the velocity and acceleration of block B and determine the velocity and acceleration of Car A relative to Car B.

  Determine the tsp emission rate of the power plant

On a clear summer afternoon with a wind speed of 3.20 m/s measured at 100 m elevation, the TSP (total suspended solids) concentration was found to be 1520 ug / m3 at a point 2 km downwind

  How to find degree of kinematic indeterminacy

how to find degree of kinematic indeterminacy

  Find probability that none of sampled items are defective

A sample of six items is drawn from this lot. Find: a) the probability that none of the sampled items are defective b) the probability that one or more of the sampled items is defective c) the probability that exactly one of the sampled items is d..

  Find the pipe friction head loss between the two points

Water flows through a pipe at 14cfs. At a point where the pipe diameter is 18in. the pressure is 30 psi; at a second point, further along the flow path and 2 ft lower than the first, the diameter is 9in. and the pressure is 18psi.

  Determine specific gravity if vol of the pot is 450ml

While washing up Grandma's old aluminum cooking pot I noticed that it would just barely touch the bottom of the sink if I added 2.5 cups of water to it. The pot is 3.5 in high and 9.5 in diameter. Thickness of aluminum is 3/16 in.

  Explain important information about short essay

Important information about Short essay, In managing the uncertainties of ethical issues in engineering, what are some questions that we may ask to limit some of the risk

  Determine the clean filter head loss in filter bed composed

Determine the clean filter head loss in a filter bed composed of 0.3 m of uniform anthracite (with an average size of 1.6 mm) placed over 0.3 m of uniform sand ( with an average size of 0.5 mm) for a filtration rate of 160 L/m^2.min.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd