What rate is nh3 is being removed from the feed gas what is

Assignment Help Mechanical Engineering
Reference no: EM13628660

A chemical plant produces an ammonia-rich waste gas that cannot be released as-is into the environment. One method to reduce the ammonia concentration in the waste gas is to bubble the waste gas through a liquid solvent. Components of the gas that are highly soluble, like ammonia, will dissolve into the liquid phase. Water is an appropriate liquid solvent for this process. The chemical plant produces 130.0 m3/hr of waste gas (? = 0.0407 mol/L) initially having a mole fraction of 0.130 NH3, and wishes to remove 90.0% of the initial amount of NH3. The maximum concentration of ammonia in water at this temperature is 0.2000 mol NH3/ mol water. Neglect the absorption of other waste gas components into the water, and the evaporation of water into the waste gas stream.

What rate is NH3 is being removed from the feed gas?What is the minimum flow rate of water required to scrub out 90.0% of the incoming NH3?What is the mole fraction of NH3 in the scrubbed waste gas stream?

Reference no: EM13628660

Questions Cloud

Answer the following using the research hypothesis there : the number of deaths due to firearms in the united states between 1968 and 1993 are given belowyearfirearm deaths
A d-cell flashlight has an emf of 150v an internal : a d-cell flashlight has an emf of 1.50v an internal resistance of 0.12 ohms and a load provided by the resistor r if
Two pieces of optically flat glass n 150 touch at one edge : two pieces of optically flat glass n 1.50 touch at one edge and a separated by a thin stretched fiber at the opposite
The room temperature yield strength of ni is 100mpa 15000 : the room temperature yield strength of ni is 100mpa 15000 psi and furthermore sy diminishes about 5mpa for every 50
What rate is nh3 is being removed from the feed gas what is : a chemical plant produces an ammonia-rich waste gas that cannot be released as-is into the environment. one method to
A spherical pressure vessel is formed of 16-gauge 00625 in : a spherical pressure vessel is formed of 16-gauge 0.0625 in cold drawn aisi sheet steel. if the vessel has a diameter
The half-life of a radioactive substance has been defined : 1 explain why almost all naturally-occurring isotopes have a greater number of neutrons than protons.2 when two small
A study comparing the resting heart rate of four different : a study comparing the resting heart rate of four different types of elite athletes recruited 10 cyclists 10 triathletes
Explain why almost all naturally-occurring isotopes have a : 1 explain why almost all naturally-occurring isotopes have a greater number of neutrons than protons.2 when two small

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd