Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Suppose that three filters, having identical first-order low pass transfer functions, are cascaded, what will be the rate at which the overall transfer function magnitude declines above the break frequency? Explain.
The input output relation of a non-linear system is y(t) = x2(t), where x(t) is the input and y(t) is the output. a. The signal x(t) is a band limited with a frequency max( max) = 2000*pi rad/sec. Determine if y(t) is also a band limited, and if so..
1. If the power gain of the amplifier is +42dB, what is the input power required to obtain the full output from the amplifier 2.If the voltage gain of the amplifier is 60dB, what is the required input voltage if the amplifier is to produce its rate..
a) Find the current out of the current source. b) Find the current through the 200-ohm resistor. c) Calculate the power delivered by the source.
The saw tooth waveform of Problem P6.5 is applied as the input to a filter with the transfer function shown in Figure P6.15.Assume that the phase of the transfer function is zero for all frequencies. Determine the steady-state output of the filter..
The total current in a semiconductor is constant and is composed of electron drift current and hole diffusion current. The electron concentration is constant and is equal to 10^17 cm^-3. The hole concentration is given by p(x)
The source-free circuit depicted in Fig. 9.1 is constructed using a 10mH inductor, a 1mF cPcitor, and a 1.5k ohm resistor. a) Calculate alpha, omega-sub-delta, and omega-sub-zero. b) write the equation which describes the current i for t>0.
A bank of induction motors cosumes 36kW at 0.78pf lagging from a 60 Hz 240V RMS line. If 200μF of capacitors are placed in parallel with the load, what is the new power factor of the total load
A conical section of material extends from 2.0 cm = r = 9.0 cm for 0 = (theta) = 30° with (permitivity) = 9.0 and (omega) = 0.020 S/m. Conductive plates are placed at each radial end of the section. Determine the resistance and capacitance of the ..
(a) The ideal delay system. y[n] = x[n-nd] (b) The accumulator system. y[n] = sum (xk) , k from -inf to n (c) Forward difference system. y[n] = x[n + 1]- x[n] (d) Backward difference system. y[n] = x[n]- x[n - 1]
a) Developed an analytical expression for |Vout/Vin|, where Vout is the voltage across the combination impedance R2||C2, and Vin is the voltage. b) For w0^2 = 1/(R1R2C1C2) (the center frequency), develop an expression for the maximum value of |Vout..
1. Provide 3 ways for creating proto-types of an electronic circuit. 2. Explain briefly, in outline form, and in your own words, the procedure for creating a single-sided, PCB (Printed Circuit Board), using the etching procedure.
If a cache being simulated were allowed to have a block size of 4 bytes, what optimization would be possible for blocks of that size that is not possible for block sizes 8 bytes and above
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd