What pressure must be provided at point 1 if you neglect

Assignment Help Civil Engineering
Reference no: EM13544578

1.From a point 1, a 25mm diameter pipe runs horizontally under the floor and then a 12.5 mm diameter line runs 1 m up the wall to a point 2. To maintain a pressure of 300kPa at point 2, what the 15 C water is flowing at 0.5 L/s, what pressure must be provided at point 1 if you neglect friction?

2.A pressure gage at elevation 4.8 m on the side of a storage tank containing oil reads 34.7 kPa.Another gage at elevation 2.2 m reads 57.5 kPa. Compute the specific weight, density, and specific gravity of the oil.

Reference no: EM13544578

Questions Cloud

What is the recommended clear zone distance : What is the recommended clear zone distance for the following roadway situations? (Use the Clear Zone nomograph to find solutions)
How to get the intensity of the rainfall from information : For a hydrology question we are given the depth of runoff and the time. We are to make a hyetograph using this information but Im not sure how to get the intensity of the rainfall from this information
What would the concentration in the effluent be 7 days later : A lagoon with volume 1200 m3 has been receiving a steady flow of a conservative waste at a rate of 100 m3/day for a long enough time to assume that steady-state conditions apply. The waste entering the lagoon has a concentration of 10 mg/L. Assuming ..
What is the minimum possible value for this pressure : Part of a vertical piping system consists of 8 ft of 4 in diameter, connected to 8 ft of 3 in diameter above, and connected to 8 ft of 2 in diameter above that. Water at 60 F flows up the pipe (no downward flow occurs)
What pressure must be provided at point 1 if you neglect : A pressure gage at elevation 4.8 m on the side of a storage tank containing oil reads 34.7 kPa.Another gage at elevation 2.2 m reads 57.5 kPa. Compute the specific weight, density, and specific gravity of the oil.
Find the steady-state concentration if the air is assumed to : Consider the air over a city to be a box 100 km on a side that reaches up to an altitude of 1.0 km. Clean air is blowing into the box along one of its sides with a speed of 4 m/s.
Suppose the utility encourages its customers to replace : Suppose a utility generates electricity with a 36 percent efficient coal-fired power plant emitting the legal limit of 0.6 lb of SO2 per million Btus of heat into the plant. Suppose the utility encourages its customers to replace their
What is the speed of the train relative to : The train is travelling at 0.8 m/s i relative to a man on the side of the tracks. What is the speed of the bug as seen by the man at the side of the tracks? What is the speed of the train relative to (or as seen by) the bug?
Determine the batch weights needed for all materials for : Determine the batch weights needed for all materials for a 1yd^3 batch yielding an f'c= 2500 psi given the following information.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute the criteical stress required for the propagation

If the specific surface energy for aluminum oxide is 0.90 J/m^2, using data contained, compute the criteical stress required for the propagation of an internal crack of length 0.40 mm.

  Calculate average f per m using an mlss of 1000 mg per l

Wastewater flow is 80 gpcd with 170 mg/l BOD and 190 mg/l suspended solids. Size the extended aeration basin and clarifier using the minimum detention time and overflow rates. Calculate the average F/M using an MLSS of 1000 mg/l.

  Determine horizontal distance between the points

What is the corresponding horizontal distance between the points - The slop distance 156.777 from one poin to another at rate of+1.5%

  Find the absolute value of the magnitude of force vector

Find the absolute value of the magnitude of force vector B if the resultant force= 1000 lb, force vector A= 1000 lb, and the resultant forms a 45 degree angle with B, and vector B runs parallel to the y axis.

  Determine what flow rate are required from the local well

a town requiring 2 cms ofwater has two sources, a local well with 15 g/m^3 of a contaminantand a distant surface water source with 2 g/m^3 of the contaminant.

  Determine maximum tensile and compressive bending stresses

A rectangular tube has an outside dimensions that are 2in wide and 4in deep and a wall thickness of 0.25in. The tube is acted on by a bending moment of 12,000lb-in.

  Calculate the ratio of the area to volume for unit cube

calculate the ratio of the area to volume for unit cube,a unit sphare inscribed inside the cube,and as right cylinder inscribed inside the cube.

  Determine what diameter pipe would be recommend

A circular concrete pipe (n = 0.012) carries a discharge of 450 cfs with a slope of 0.008 and is designed to run no more than 60% full (by depth). What diameter pipe would you recommend

  Determine the magnitude and directional sense of moment

The railway crossing gate consists of the 100 kg gate arm having a center of mass at Ga and the 250 kg counterweight having a center of mass at Gw.

  Probelm related to when object is thrown downward

An object is thrown downward from a 150-ft cliff with a velocity of 45m/hr so that it makes an angle of 60° with vertical face of the cliff.

  What is the weight of the c-clamp at sea level in newtons

The C-clamp weighs 14 oz at sea level. [16 oz (ounces) = 1lb.] The acceleration due to gravity at sea level is g = 32.2 ft/s2. a) What is the mass of the C-clamp in slugs b) What is the weight of the C-clamp at sea level in Newtons

  How many customers would be served pertruck if each home has

Making two runs per day, how many customers would be served pertruck if each home has once-per-week service and the truck is usedfive days per week?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd