What percentage of the shafts will be within tolerance

Assignment Help Civil Engineering
Reference no: EM131065258

The specification for the length of a shaft is 12 inches ±.001 inch. If the process standard deviation is .00033, approximately what percentage of the shafts will be within tolerance?

Reference no: EM131065258

Questions Cloud

Are the arguments logical and consistent : Identify the document/source--what type of document/source is it and when was it written? Does the writing concern the past, present or future? What is the time gap between the time of writing and the time of the issues/information being recorded?
Construct a spreadsheet to calculate the payback period : Construct a spreadsheet to calculate the payback period, internal rate of return, modified internal rate of return, and net present value of the proposed mine. You must submit the spreadsheet.
Determinants of trade flows-financing international trade : "Determinants of Trade Flows and Financing International Trade" Please respond to the following: Analyze the major effects that microeconomic and macroeconomic factors could have on the international flow of funds between countries and the primary ma..
Discuss two recommendations the authors make : From the first e-Activity, discuss two recommendations the authors make regarding the applicability of performance budgeting to the current United States government.
What percentage of the shafts will be within tolerance : what percentage of the shafts will be within tolerance?
Compute the householder matrix : Let a = (2.6, 4.7)T. Consider  the floating-point algorithm with  3 digit rounding. Compute the Householder matrix Q generated by a as a 2x2 array. (Remember to round each computation to 3 digit)
Low pass fir digital filter project using microcontroller : To design digital FIR low pass filter and to implement the FIR low pass filter using microcontroller and to get a linear phase response.
What is the portfolio beta if your portfolio is comprised : What is the portfolio beta if your portfolio is comprised of 30 percent of stock X, 20 percent of stock Y, and 50 percent of stock Z. Stock X has a beta of 1.21, stock Y has a beta of 1.38, and stock Z has a beta of 0.35.
Calculate whether the process is capable or not : calculate whether the process is capable or not.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the final temperature of the steam and the heat in

Two kilograms of steam at 300kPa and a quality of 75% are heated in a closed container until a pressure of 600kPA is reached. Determine the final temperature of the steam and the heat input. Find the pressure at which saturated water vapor is obtaine..

  Design simple horizontal curve to connect roadway tangents

Design a simple horizontal curve to connect two roadway tangents that deflect at an angle chosen between 50 and 75 degrees. Assign a station to the curve PI and select a curvature of 6 degrees.

  Theoretical analysis of carbo fibre reinforced polymer

The theoretical analysis of carbo fibre reinforced polymer composite for cable stayed bridges using ansys program

  Determine the final maxture dry bulb temperature

one atmospheric air stream at 15 c and 30 percent relative humidity is mixednadiabatically with another air stream at 30c and 70 percent relative humidity in a steady flow process

  What real-world considerations absent in the problem

The mayor proposes financing the museum with a lump-sum tax of $24 and then opening the museum free to the public. How many times would each person visit? Calculate the benefit each person would get from the musuem, measured as consumer surplus minus..

  Make reasonable assumptions as to the soil properties

Soil borings made at a site near Chicago indicate that the top 6m is lose and miscellaneous fill, with the groundwater table at 3m below the ground surface. Below this is a fairly soft blue-gray silty clay with an average water content of 30%. The bo..

  Determine what is the concentration of particles in the air

A hi-vol clean filter weighs 18.00 g. After a 24 hour sampling period the filter is removed and weighs 18.65 g. The initial flow rate through the filter was 2.5 m3/min.

  What is the maximum elevation of the reservoir above

A 150 L helium tank contains pure helium at a pressue of 1825 psig. How many 3.5L helium balloons can be filled from the helium  in the tank? (Assume an atmospheric pressue (14.7 psia) and a temp of 298K.

  If the property can be sold what is the rate of return

An investor has invested $250,000 in a new rental property. Her estimated annual costas are $6,000 and annual revenues are $20,000. What rate of return per year will the investor make over a 30-year period ignoring

  Determine the maximum force that can safely applied

Determine the maximum force (P) that can safely applied to a steel tee section (20 feet in length) with the point loads at 5 feet from each end. Fixed at one end, pin at the other.

  Determine the corresponding increase in water temperature

Water flows over a waterfall that is 60m high. Assuming that all of the potential energy of the water at the top of the fall is converted to an increase in internal energy at the bottom of the fall

  What fraction of the tank air mass will be consumed

The divers work at a depth of 15 m and the seawater density is 1027 kg m-3. They are known to consume 130 litres of air at the ambient temperature is 10oC over the time taken to do the job.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd