What must the temperature of the saturated liquid water

Assignment Help Mechanical Engineering
Reference no: EM13712618

An initially empty, well insulated, rigid tank with a volume of 2 m3 is fitted with a mixing device. The tank has two inlets and zero outlets. One inlet is water at 1.07 MPa and 630oC while the other is saturated liquid water. Both enter the tank slowly. If the amount of work done by the mixing device is 300 kJ, what must the temperature of the saturated liquid water be if the same mass is added through both inlets and the final state is at 300 kPa with a specific volume of 0.5 m3/kg?

Reference no: EM13712618

Questions Cloud

Find the indicial equation and its roots : Find the indicial equation and its roots. Find the recurrence relation. Use the recurrence relation to find the first three terms of the power series solution corresponding to one root of the indicial equation
Silicon rubber drain hose for surgical procedure : Silicon rubber has a Poisson’s ratio of 0.4. Consider a silicon rubber drain hose for a surgical procedure; the hose has an outer diameter of 4 mm and a wall thickness of 0.5 mm. How much does the lumen (interior space) of the catheter constrict if t..
Calculate the mole fraction of methane in the fuel : A fuel gas containing methane and ethane is burned with air in furnace, producing a stack gas at 300C and 105kPa (absolute). The stack gas contains C02 at a partial pressure of 80 mm Hg and no CO,O2, methane or ethane. Calculate the mole fraction of ..
Calculate the fluid acceleration : Consider a two dimensional flow X-Y plane (no motion in Z direction). The Velocity field is going by : Y/(X^2+Y^2) and V= -x/(X^2+Y^2). Determine the equation of streamline passing through point X=0 and Y=5. Calculate the fluid acceleration
What must the temperature of the saturated liquid water : An initially empty, well insulated, rigid tank with a volume of 2 m3 is fitted with a mixing device. The tank has two inlets and zero outlets. One inlet is water at 1.07 MPa and 630oC while the other is saturated liquid water. Both enter the tank slo..
Find the pressure-temperature and mach number at the exit : An air nozzle has an exit area 1.6 times the throat area. If a normal shock occurs at a plane where the area is 1.2 times the throat area, find the pressure, temperature, and Mach number at the exit. The stagnation temperature and pressure before the..
Neglecting kinetic energy and potential energy effects : Air, modeled as an ideal gas, is compresses at steady state from 1 bar, 300 K, to 5 bar, 500K, with 150 kW of power input. Heat transfer occurs at a rate of 20 kW from the air to cooling water circulating in a water jacket enclosing the compressor. N..
Calculate the heat transmission through the wall : An outside wall of a building is constructed of 1/2 inch gypsum sheeting, 8 inches of concrete block (hollow, 3 oval core), and 4 inches of common brick. The inside of the building is maintained at 75F dry-bulb temperature and 65F wet-bulb temperatur..
Determine the design heating load due to infiltration : A large manufacturing space with an average floor to ceiling height of 30 ft has a floor area of 5000 ft^2. The total infiltration rate for the space is estimated to be 1.5 air changes per hour. The inside design temperature and relative humidity are..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd