What must be the distance be between filaments 2 and 3

Assignment Help Electrical Engineering
Reference no: EM13256323

Three infinitely-long filaments of current are lined up parallel to the z axis. Filament 1 is on the left, filament 2 is in the middle, and filament 3 is on the right. Filaments 1 and 2 have currents of 1 A in the ba z direction, and filament 3 has a current of 2 A in the ba z direction. If the distance between filaments 1 and 2 is 1 m, what must the distance be between filaments 2 and 3 to make the net force on filament 2 zero? If the net force can't be zero, explain why.

Reference no: EM13256323

Questions Cloud

Determine efficiency of transformer for secondary current : A single-phase, 100-kVA, 1000:100-V, 60-Hz transformer has the following test results: Open-circuit test (FIV side open): 100 V, 6 A, 400 W Short-circuit test (LV side shorted): 50 V, 100 A, 1800 W 1)Determine the voltage regulation at 75% of the rat..
Describe some aspect of the earth in space : Write a paragraph essay describing some aspect of the earth in space. Attached is a reference for material. This needs to be using strict APA format.
Find magnitude of the emf induced in the secondary winding : A very long, straight solenoid with a cross-sectional area of 2.30cm2 is wound with 93.4turns of wire per centimeter. What is the magnitude of the emf induced in the secondary winding at the instant that the current in the solenoid is 3.2
What is the companys after-tax return on the preferred : Your corporation has a marginal tax rate of 35% and has purchased preferred stock in another company. The before-tax dividend yield on the preferred stock is 12%. What is the company's after-tax return on the preferred, assuming a 70% dividend exc..
What must be the distance be between filaments 2 and 3 : Filament 1 is on the left, filament 2 is in the middle, and filament 3 is on the right. Filaments 1 and 2 have currents of 1 A in the ba z direction, and filament 3 has a current of 2 A in the ba z direction
Find the maximum electric field strength at given distance : An AM radio transmitter broadcasts 47.0 kW of power uniformly in all directions, What is the maximum electric field strength at this distance
What would be the cost of that capital : If a company is going to finance a project entirely with retained earnings, what would be the cost of that capital? Why?
Are these methods effective : What methods can be used by the FED to influence interest rates? Are these methods effective? Use examples where appropriate.
Molecules are excluded from an enzyme''s catalytic pocket : When free water molecules are excluded from an enzyme's catalytic pocket, is a catalytic -OH group a stronger or weaker nucleophile? Explain your reasoning.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the voltage at coil 2 and the flux through coil 1

Two coupled coils have self-inductances L1 = 50 mH and L2 = 200 mH, and a coefficient of coupling k = 0.5. If coil 2 has 1000 turns, and I1 = 5Sin (400t) (i.e. the phasor current is 5? -90° A). Find the voltage at coil 2 and the flux through coil ..

  Find the probability that a transmitted bit is received

A variant of the binary symmetric communication channel described in class is called a binary erasure channel. The transmitter sends a ‘0' or ‘1,' but at the receiver there are three possibilities: a ‘0' or ‘1' or ‘undecided bit..

  Design the controller and estimator for closed-loop system

design the controller and estimator so that the closed-loop unit step response to a command input has a rise time tr

  Determine primary nad secondary turns

The maximum flux density in the core of a 250/ 3000 volts, 50 Hz single phase transformer is 1.2 Wb/m2. if the emf per turn is 8 volt, determine (i) primary nad secondary turns (ii) area of the core

  Find the total circuit impeadance and current source

Find the associated answers for: total circuit impeadance (Zt), Current source (RMS), Vc (RMS) w/ power factor, Vr (RMS), all in complex form/ rectangular form. Remember each question has to be done three times, one for each frequency.

  What fraction of the input power makes it to the output

Find the maximum allowed developed torque and corresponding motor speed that will ensure that no more than 25% of the power is lost in conductive losses in the armature and field windings.

  Determine the direction of current in a multiloop circuit

how do we determine the direction of current in a multiloop circuit with more than one source of e.m.f?

  How much time in seconds will it take to rotate the part

The steering wheel has backlash. This means there is a delay between the time the wheel is turned, and the time the car responds. The driver tends to overturn, which leads to instability and lack of control of the car.

  Design 3 stage amplifier with the input signal

Design 3 stage amplifier with the following requirement input signal = 5 mV with R=10k ohms over all gain > 1000 power supply: Vcc = 5V, Vee = -5V Rin > 1 Mega Ohms Rout = 100 ohms 1st Stage BJT must use inverting

  Define the efficiency of the motor and drive system

If the efficiency of the motor and drive system is 80% and it is fed through a transistor regulator at 12V, what is the mean current through this regulator when the printer is working continuously?

  What is the difference in the filtered signals spectrum

A signal contains a mixture 30 , 100 and 240 Hz Sine waves and also contains wideband noise whose spectrum is from 500 Hz up to a 1000 Hz. Describe a filtering technique that can be used to cleanly separate 30, 100 and 240 Hz from each other and a..

  Estimate of the maximum fundamental operating frequency

Using the LM555 data sheet, make an estimate of the maximum fundamental operating frequency in the astable mode.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd