What motor efficiency at full load and unity power factor

Assignment Help Electrical Engineering
Reference no: EM13967418

A 2300-V 2000-hp 0.8-PF leading 60-Hz two-pole Y-connected synchronous motor has a synchronous reactance of 1.5Ω and an armature resistance of 0.3Ω. At 60 Hz, its friction and windage losses are 50 kW, and its core losses are 40 kW. The field circuit has a dc voltage of 200 V, and the maximum IF is 10 A. The open-circuit characteristic of this motor is shown in Figure. Answer the following questions about the motor, assuming that it is being supplied by an infinite bus.

(a) How much field current would be required to make this machine operate at unity power factor when supplying full load?

(b) What is the motor's efficiency at full load and unity power factor?

(c) If the field current were increased by 5 percent, what would the new value of the armature current be? What would the new power factor be? How much reactive power is being consumed or supplied by the motor?

(d) What is the maximum torque this machine is theoretically capable of supplying at unity power factor? At 0.8 PF leading?

2401_nm.png

Reference no: EM13967418

Questions Cloud

While recognizing the non finance accounting staff as expert : Value of this project: To adapt your communication and managerial accounting concepts to non-accounting/finance colleagues while understanding and appreciating their contributions to the enterprise. Refer to the concepts and break them down so others
Determining the cartel equilibrium : The Hand Tool Manufacturing Industry Trade Association recently published the following estimates of demand and supply relations for hammers:
Calculating the competitive strategy : Gray Computer, Inc., located in Colorado Springs, Colorado, is a privately held producer of high-speed electronic computers with immense storage capacity and computing capability. Although Gray's market is restricted to industrial users and a few ..
Monopolistically competitive equilibrium : Soft Lens, Inc., has enjoyed rapid growth in sales and high operating profits on its innovative extended-wear soft contact lenses. However, the company faces potentially fierce competition from a host of new competitors as some important basic pat..
What motor efficiency at full load and unity power factor : The field circuit has a dc voltage of 200 V, and the maximum IF is 10 A. The open-circuit characteristic of this motor is shown in Figure. Answer the following questions about the motor, assuming that it is being supplied by an infinite bu..
Compliance issues of the federal procurement framework : Analyze the proposal adequacy checklist for organizing a proposal, and summarize the intrinsic value of two (2) of the suggestions on the checklist.
Which rocks deform and the chemical and physical factors : Identify the ways in which rocks deform and the chemical and physical factors that are involved in the deformation process.
What behaviors do you look for when building your teams : What behaviors do you look for when building your teams? Discuss what you believe are the most critical things to consider when forming a team.
Monopolistically competitive demand : Would the following factors increase or decrease the ability of domestic auto manufacturers to raise prices and profit margins? Why?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate what standard size copper cable will give at motor

A tractor-trailer truck driver friend often delivers to companies that do not have a fork truck or loading dock. She wants to install a lift-gate on her trailer so she can load and unload her truck without a fork truck.

  What is the difference between the wavelengths

isible light passes through a diffraction grating that has 900 slits per centimeter, and the interference pattern is observed on a screen that is 2.58 m from the grating. In the first-order spectrum, maxima for two different wavelengths are separat..

  Find the resistance of an electric light bulb for a current

1.) Find the resistance of an electric light bulb if there is a current of a 0.8 A and a voltge potential diference of 120V. 2.) A light bulb uses 1.2A when connected across a 120Vsource. What power is used by the bulb

  What is min sampling frequency to mixed signal

What is the minimum sampling frequency to be able to avoid aliasing if your system has 10Hz, 100Hz and 1500Hz mixed in a signal

  What is the rms voltage across the transformer secondary

a full wave center-tapped transformer rectifier in a power supply provides an average dc output voltage of 14 v on which a maximumripple of +,-0.5 volt is allowed.Diodes have a 0.7 volt drop when conducting.

  1draw a relay construction diagram and briefly explain the

1.draw a relay construction diagram and briefly explain the operation of a relay.2.define the terms normally open and

  Determine transformers equivalent inductive parameters

Discuss the methods used for finding the approximate transformer parameters Rser, Lser, Rpar, and Lpar and explain what each of the parameters Rser, Lser, Rpar, and Lpar model and show their positions in the transformer's circuit diagram.

  Determine what is the value of r across the inductor

consider an inductor with an inductance of 150mH and winding resistance of 50Ω. if the inductor is in parallel with a 2R resistor and both are in series with another resistor, R. if the voltage across the inductor is 6V after 15μs, what is the val..

  How to implement the cache protocol to support a state

Many multiprocessors distinguish between a cache block that is really shared and one that exists in the clean state in exactly one cache. The addition of a "clean and private" state eliminates the need to generate a bus transaction on a write to s..

  What is the ratio of galvanometer current to maximum range

A meter being used for a 2-wire resistance measurement has an internal current source of 1 mA. If the meter's test leads have equal resistances of 0.06-ohm, what is the measured resistance for: A resistor of actual value 0.5-ohm

  Find the system power gain in db and the system noise ratio

An amplifier with a power gain of 3dB is to be characterized. The test apparatus provides a SNR of 20dB at the input and measures a SNR of 15dB at the output. Find the amplifier's NF. Specifications for (2), (3), (4) and (5).

  Find what size resistor should be placed between r4 and r5

Determine(using the thevenin equivalent circuit) what size resistor should be placed betweent R4 and R5 to ensure that resistor receives the maximum power possible from the power source

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd