User Account

All Pages

What maximum internal pressure can be applied

Assignment Help Mechanical Engineering
Reference no: EM131122798

Question - An external pressure of 10 MN/m2 is applied to a thick cylinder of internal diameter 160 mm and external diameter 320 mm. If the maximum hoop stress permitted on the inside wall of the cylinder is limited to 30 MN/m2, what maximum internal pressure can be applied assuming the cylinder has closed ends? What will be the change in outside diameter when this pressure is applied? E = 207 GN/m2, v = 0.29.

Reference no: EM131122798

Questions Cloud

Discuss each of the directors contentions : In response, the directors argue that: (1) no illegal activity had occurred; (2) if an illegal activity did occur, it was not at a valid meeting of the corporation and was therefore not an official action of the board; and (3) if they had to legal..
Determine the normal force in bar : A pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 70 GPa] with a cross-sectional area of A1 = 2,400 mm2. determine the normal force in bar (1)
Define a normal profit and an economic profit : Define a normal profit and an economic profit. Are normal profits being earned in this example? Are economic profits present for this firm in this example? Explain your answers.
Describe a sensor that would give an electrical output : Feedback control requires being able to sense the variable being controlled. Because electrical signals can be transmitted, amplified, and processed easily, often we want to have a sensor whose output is a voltage or current proportional to the va..
What maximum internal pressure can be applied : If the maximum hoop stress permitted on the inside wall of the cylinder is limited to 30 MN/m2, what maximum internal pressure can be applied assuming the cylinder has closed ends
Describe an actuator that could accept an electrical input : Feedback control requires being able to sense the variable being controlled. Because electrical signals can be transmitted, amplified, and processed easily, often we want to have a sensor whose output is a voltage or current proportional to the va..
Review membership requirements and member benefits : Review membership requirements and member benefits and compare your interests and what you want from a networking organization to the benefits and mission statement offered by the organizations you identify (Costello, 2012).
Determine the tension in cable bo immediately : The homogeneous thin bar AB shown below has a mass of M and a length of L. The bar is supported by lightweight, inextensible cable BO at end B and by a smooth, inclined wall at end A. Determine the tension in cable BO immediately after the bar is r..
Journalize the entries to record the transactions : The following selected transactions were completed by Artic Company during February of the current year. Artic Company uses the periodic inventory system.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd