What maximum force can this person apply with the jack

Assignment Help Civil Engineering
Reference no: EM13314341

A person of mass 80kg places all their weight on the pedal of a foot operated hydraulic jack. The diameter of the hydraulic cylinder under foot pedal is 4cm and the diameter of the jack cyclinder is 9cm (Assume g is 9.81 m/s^2)

What maximum force can this person apply with this jack.

Reference no: EM13314341

Questions Cloud

Calculate the overall speedup of a system : Calculate the overall speedup of a system that spends 65% of its time on I/O with a disk upgrade that provides for 50% greater throughput.
Explain how to calculate the mcl for the acceptable risk : the water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE
Determine the speed of the arrow after traveling from rest : A bowstring produces a force against a 2.0 oz arrow given by where a = 40 lbf, b = 3.2 ft-1 and x is in ft. x = 0 when the arrow is pulled fully back and increases as the arrow moves forward.
What input of power rating is required for pump to refill : A water storage tank located on a larege dairy farm has a storage capacity of 0.1 ML. The average rate of water consumption from this tank is 6.25 kL per day, every day. The farmer refills the tank (overnight) every 14 days
What maximum force can this person apply with the jack : A person of mass 80kg places all their weight on the pedal of a foot operated hydraulic jack. The diameter of the hydraulic cylinder under foot pedal is 4cm and the diameter of the jack cyclinder is 9cm (Assume g is 9.81 m/s^2)
Find what is the expected compression of the 4 springs : The undercarriage for an aircraft uses two springs between each wheel and the aircraft fueselage to cuhion the landing of the aircraft. There are two sprung wheels and the mass of the aircraft is 5000kg
What is the rate of fuel used by the engine in the test : A container of petrol on a set of scales is used to measure the rate at which fuel is used by an engine under test. In one test the weight measured by the scales decreases by 25.0 N in 1 hour.
Find out the uncertainity in its position : A baseball is 150g and thrown at 100miles/hour with the same uncertainity. Determine the uncertainity in its position. The uncertainity was set at 1% in the previous problem not sure if it matters pertain to this problem.
Calculate the average frictional force that stops the bullet : A 7.80-g bullet moving at 640 m/s penetrates a tree trunk to a depth of 6.1 cm. find the average frictional force that stops the bullet

Reviews

Write a Review

Civil Engineering Questions & Answers

  What would the gross truck mass when loaded to heap capacity

If a truck has a capacity of 24m^3 (Heaped) and 18m^3 (struck), with a total empty weight of 31600kg (truck), and needs to move soil at a density of 1850kg.m^3 (Bank) with a swell of 41%

  Tape corrections under following conditions

The tape is stretched over three equal spans. Calculate the tape corrections under the following conditions at field, temperature = 85ºF, pull = 18kg, E= 2.109 x 10 6 kg/cm 2

  Standard test method for flash and fire points

What is the procedure standard test method for flash and fire points by cleveland open cup tester if there is animation or video is better....

  How to derive the unit hydrogaph by the inverse procedure

Given below are the measured stream flows in cfs from a storm of 6-hour duration on a stream having a drainage area of 185 mi^2. Derive the unit hydrogaph by the inverse procedure. Assume a constant base flow of 550cfs.

  Find what design speed was used for freeway exit ramp

A freeway exit ramp has a single 12-foot lane and consists entirely of a curve with a central angle of 90 degrees and L=628 feet. If the distance cleared of obstacles is 19.4 feet from the centerline, what design speed was used

  Determine magnitude and location of resultant force acting

The tank contains water to depth of 2m and oil (SG=0.8) on top of the water to a depth of 1m. Determine the magnitude and location of the resultant force acting on one end of the tank (i.e. 3m high by 3m wide).

  How much larger should street name be in order to be legible

street nam sizes on the signs at a certain location can be discerned by a person with 20/40 vision from a distance of 300 ft. how much larger should the street names be in order to be legible to a person with 20/50 vision from a distnace of 450 ..

  Determine the concentration of ubod in the effluent

If the length of the river connection between the two lakes is equal to 3km and the velocity in the river is equal to 0.4 m/s, determine the concentration of UBOD in the effluent from the second lake.

  Determine an appropriate plywood thickness and span rating

For a total floor load of 75 psf on 2x floor framing at 24 o.c., determine an appropriate plywood thickness and span rating assuming panels with edge support and panels oriented perpendicular to the framing. Specify the minimum fasterners and spac..

  What quantity of ice melts

A 3.60-g lead bullet at 28.0 degrees C is fired at a speed of 230 m/s into a large block of ice at 0 degrees C, in which it embeds itself. What quantity of ice melts?

  Determine the overall specific weight of each of the samples

Two soil samples, each having a void ratio of 0.76 and density of 2.65 grains have degrees of saturation, respectively, 85% and 100%. Determine the overall specific weight of each of the samples.

  What is the over consolidation ratio of the soil

an increment of vertical stress of 150kpa compress the sample to a void ratio of1.43. what is the over consolidation ratio of the soil at the unloaded condition.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd