User Account

All Pages

What mass of nitrogen was produced

Assignment Help Chemical Engineering
Reference no: EM131158824

A 15.0-L flask containing a sample of nitromethane is filled with O2 and the flask is heated to 100.ºC. At this temperature, and after the reaction is complete, the total pressure of all the gases inside the flask is 950. torr. If the mole fraction of nitrogen (xNitrogen ) is 0.134 after the reaction is complete, what mass of nitrogen was produced?

Reference no: EM131158824

Questions Cloud

Idea of copyright-intellectual property : What has the web done to the idea of copyright & intellectual property? Has it made it more complicated? Simpler? Will the web offer new opportunities for copyright holders? Or will the web destroy the concept of copyright & intellectual property ..
What is the edge length of the cube of uranium : The final temperature of the uranium and deuterium oxide mixture is 28.5C. Given the densities of uranium (19.05 g/cm3) and deuterium oxide (1.11 g/mL), what is the edge length of the cube of uranium?
Light savings occur : Why does day light savings occur and what day does it start?
Create a select querybased on the tblpatient table : Create a new index for the tblTherapist table based on the Lastfield. The index should Allow for duplicate values. Save and close the tblTherapist table. Create a Select querybased on the tblPatient table.
What mass of nitrogen was produced : If the mole fraction of nitrogen (xNitrogen ) is 0.134 after the reaction is complete, If the mole fraction of nitrogen (xNitrogen ) is 0.134 after the reaction is complete, what mass of nitrogen was produced?
Explain your current fitness and nutritional habits : Identify and describe 3 goals you can set to improve your physical and/or mental health. Explain some of the health risks associated with poor physical health. Explain some of the health risks associated with excess stress.
Design and simulate wien bridge oscillator using ic op-amp : The objective of this assignment is to design and simulate Wien Bridge oscillator using IC Op-amp and calculate of its frequency oscillation.
What amount of heat is necessary to synthesize no2(g) : If 2.50  102 mL of N2(g) at 100.C and 3.50 atm and 4.50  102 mL of O2(g) at 100.C and 3.50 atm are mixed, what amount of heat is necessary to synthesize NO2(g)?
Researcher with ministry of transportation : A researcher with Ministry of Transportation is commissioned to study the drive times to work (one-way) for U.S. cities. The underlying hypothesis is that average commute times are different across cities.

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Find the starting current and the starting torque

If a wye-delta starting method is employed, find the starting current and the starting torque.

  Calculate the amount of heat associated with this process

Calculate the amount of work necessary for the reversible compression of 1 kg of steam from 3 bar to 7 bar. The compression is to take place in a cylinder fitted with a weightless piston at the constant temperature of 250 °C. Calculate the amount ..

  Conclusions about photosynthesis

When algae growing in water containing only 16O were furnished carbon dioxide containing 18O, no 18O was found to be evolved from the oxygen gas produced. What conclusions about photosynthesis can be drawn from these experiments?

  Determine which heat exchanger is cheaper

determine which heat exchanger is cheaper by comparing the capitalized costs.

  What processing should be done on the computer to recover

A strap, instrumented to measure stretch, is worn around the chest to detect respiration whilst a subject is at-rest. The resulting signal is contaminated by electrical noise from the mains at 50 Hz with a similar amplitude to the respiration sign..

  Determine the slip at maximum torque and slip full load

A three-phase induction motor, operating at its rated voltage and frequency, develops a starting torque of 1.6 times the full-load torque and a maximum torque of 2 times the full-load torque. Neglecting stator resistance and rotational losses, and..

  Fact that other more pressing interests

Is our "technological distraction" contributing to the fact that other more pressing interests like the cure for cancer have not been achieved?

  Estimate the temperature of saturated steam

Estimate the temperature of saturated steam which must be used when the exchanger is new (i.e., no scale present) if the water enters the unit at a rate of 15,000 gph and is heated from 70 to 150°F.

  Calculate the binding energy in j/nucleon for carbon-12

The most stable nucleus known is 56Fe (see Exercise 38). Would the binding energy per nucleon for 56Fe be larger or smaller than that of 12C or 235U? Explain.

  Define stoichiometry of ammonia synthesis

Stoichiometry of Ammonia Synthesis, Show that the maximum concentration of NH3 is obtained in an ammonia synthesis process when the ratio of nitrogen to hydrogen

  How many neutrons and particles produced in fission reaction

How many neutrons and -particles are produced in this fission reaction? Explain in detail the process in which you arrived at you answer, and show your work.

  Determining the final temperature

If a mixture of 5.0 g of hydrogen and 10. g of methane is burned, and the heat released is transferred to 50.0 g of water at 25.0C, what final temperature will be reached by the water?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd