What magnitude of dipole strength has to be associated

Assignment Help Electrical Engineering
Reference no: EM13286548

A certain sample of pure quartz has a dielectric constant of 3.8, dielectric strength of 1.0 kV/0.0010 in, and a density of 2.6 Mg/m3.
Assume the number density of dipoles in quartz is the same as the number density of SiO2 units. What magnitude of dipole strength has to be associated with these units under to support the polarization found under a field of 5.0 kV/cm?

Reference no: EM13286548

Questions Cloud

Determine the polarization of certain sample of pure quartz : A certain sample of pure quartz has a dielectric constant of 3.8, dielectric strength of 1.0 kV/0.00010 in, and a density of 2.6 Mg/m3. a.)A field of 5.0 kV/cm is applied. Determine the polarization.
What is the maximum horizontal range of your gun : You buy a plastic dart gun, and being a clever physics student you decide to do a quick calculation to find its maximum horizontal range. What is the maximum horizontal range of your gun
In which ratios would each group be most interested : If we divide users of ratios into short-term lenders, long-term lenders, and stockholders, in which ratios would each group be most interested, and for what reasons?
Find the density of an unknown material : In order to find the density of an unknown material Susan measured the mass of a cube made out of this material and the length of its side
What magnitude of dipole strength has to be associated : A certain sample of pure quartz has a dielectric constant of 3.8, dielectric strength of 1.0 kV/0.0010 in, and a density of 2.6 Mg/m3. Assume the number density of dipoles in quartz is the same as the number density of SiO2 units.
Find the velocity of the player after he catches the puck : a 70 kg hockey player sliding freely on his knees on horizontal icy surface with velocity m/s. find the velocity of the player after he catches the puck
Define what is the final volume of oxygen gas : A syringe containing 1.42 mL of oxygen gas is cooled from 99.7 C to 0.6 C. What is the final volume of oxygen gas
Define the volume of the gas is increased : A sample of gas has an initial volume of 2.8 L at a pressure of 753 mmHg .If the volume of the gas is increased to 3.6 L, what will the pressure be
Determine the maximum torque exerted on the coil : You have a wire of length L = 1.9 m for making a square coil of a dc motor. The current in the coil is I = 1.6 A, Find the maximum torque exerted on the coil

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How parameters must be constrained to make system constant

In the question below only focus on the parameter or parameters that are relevant to the particular property you are being asked about in the particular question. If you need to constrain a parameter to satisfy the stated criterion.

  Find the values of l and c and the cutoff frequencies

Design a series resonant circuit to have a bandwidth of 400 Hz using a coil with a Ql of 20 and a resistance of 2. Find the values of L and C and the cutoff frequencies.

  Find how many electrons flow out of the battery

if an automobile battery delivers 120 A when the car is being started, and the starting process takes 6 seconds, how many electrons flow out of the battery

  Determine what rc time constant must the filter have

Sketch the schematic for a RC low-pass filter with a 3 dB cutoff frequency of 500 Hz, i.e., the output at 500 Hz is 1/2 = 0.707 of the filter output at DC. What RC time constant must the filter have

  Compare the three rectifier to design a 20 v supply

Compare the three rectifier ( half wave, full wave and bridge rectifier) to design a 20 V supply with 1V ripple for a 1Kiloohms load. In the comparison look for the filter capacitor, transformer turn ratio n and the PIV of the diodes.

  What are the x and y componenets of its acceleration

A small object with mass 3.20 kg moves counterclockwise with constant speed 5.50 m/s in a circle of radius 4.20 m centered at the origin. It starts at the point with position vector (4.20i hat + 0 j hat ) m. T

  Find the required x-y coordinates of a 20 nc fourth charge

Three point charges are positioned in the x-y plant as follows: 5 nC at y=5 cm, -10 nC at y=-5 cm, and 15 nC at x=-5 cm. Find the required x-y coordinates of a 20 nC fourth charge that will produce a zero electric field at the origin.

  Determine running impedance of motor in cartesian coordinate

A 120V, 60Hz AC induction motor is in parallel with a power factor correction capacitor. The capactior has a value of 50 micro Farads and produces a minimum line current of 2 ohms. Determine the running impedance of the motor in cartesian coordina..

  Sketch the dft

Sketch the DFT(discrete fourier transform)for a square wave with frequency 1Hz and 10 Hz given N=64 and SR(sample rate)=128. Make sure to label your axes.

  Impact of electron energy

Briefly discuss the impact of electron energy, electron current and target on the Bremsstrahlung generated.

  Find the eb-no ratio in db for a system operating

Find the Eb/no ratio in dB for a system operating at 10Mbps in a BW of 1MHz. the un-modulated carrier power is 0.1pW and the system noise temperature is 120 degrees Kelvin.

  What is the maximum angle the shaft can turn

a 350° pot is connected to a shaft through a 3:1 gear ratio a. What is the maximum angle the shaft can turn b. What is the maximum difference in degrees from where the shaft is and where the pot reports is to be

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd