User Account

All Pages

What load rating should be used to enter the timken company

Assignment Help Mechanical Engineering
Reference no: EM13622693

A straight roller bearing is subjected to a radial load of 12 kN. The life is to be 4000 h at a speed of 750 rev/min. What load rating should be used to enter the Timken Company catalog where it rates the bearings for 3000 h at 500 rev/min?

Reference no: EM13622693

Questions Cloud

Bifocal lenses are used to correct her vision what power : sometimes a person cannot clearly see objects close up or far away. to correct this type of vision bifocals are often
The player pulls his hand back during the impact at an : a baseball player catching a ball can soften the impact by pulling his hand back. assuming that a 5-oz ball reaches his
The need for health care among prisoners in the three types : a researcher wants to know whether the need for health care among prisoners varies according to the different types of
A cylindrical cistern constructed below ground level is 26m : a cylindrical cistern constructed below ground level is 2.6m in diameter and 2.0 m deep and is filled to the brim with
What load rating should be used to enter the timken company : a straight roller bearing is subjected to a radial load of 12 kn. the life is to be 4000 h at a speed of 750 revmin.
Scores on an endurance test for cardiac patients are : scores on an endurance test for cardiac patients are normally distributed with the mean185 and standard deviation10.a.
It is estimated that 20 of the athletes competing in a : it is estimated that 20 of the athletes competing in a large tournament are users of an illegal drug to enhance
In a newtons rings demonstration using 540-nm light the : in a newtons rings demonstration using 540-nm light the distance from the center of the rings to the first bright ring
200 draws are made with replacement from a box of numbered : 200 draws are made with replacement from a box of numbered tickets these tickets are labeled either -2 or 3. is it

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Knowing that it strikes the water 4s after release

a stone is thrown vertically upward from a point on a bridge located 40m above the water. knowing that it strikes the

  Use psychrometric chart to determine latent portion

Use Psychrometric chart to determine Latent portion

  Sketch the cycle on p-v coordinates

One kilogram of air as an ideal gas executes a Carnot power cycle having a thermal efficiency 50%. The heat transfer to the air during isothermal expansion is 50 kJ. At the end of the isothermal expansion, the pressure is 574 kPa and the volume is..

  Use your equation to calculate the pressure in mb at 1200 m

assume that in a certain area the atmospheric lapse rate ?gamma subscript actual is equal to zero from the ground up to

  Calculate the work done by the gases assuming they can be

after a combustion process in a cylinder the pressure is 1200 kpa and the temperature is 350 c. the gases are expanded

  A what is the approximate ductility el of a brass alloy

a what is the approximate ductility el of a brass alloy that has a yield strength of 275 mpa? what is the tensile

  Find the maximum permissible unbalance

A centrifugal pump, weighing 600N and operating at 1000 rpm, is mounted on six springs of stiffness 6000 N/m each. Find the maximum permissible unbalance in order to limit the steady-state deflection to 5mmm peak-to-peak.

  The rods are connected with gears having radii of 120 and

the rods ab and cd each have a 30-mm diameter and are 1m long. the modulus of the rods is 28 gpa. the rods are

  Find out a compression ratio and inlet pressure

Also find out a compression ratio and inlet pressure to give maximum imep. engineering fundamentals of internal combustion enignes - pulkrabek.

  Heat transfer occurs until the volume on the inside of the

a piston-cylinder device contains 1 kg of h2o. the water is at 800oc and a pressure of 20 mpa. heat transfer occurs

  A flat-plate collector 4m2 in area is tested during the

a flat-plate collector 4m2 in area is tested during the night to measure the overall heat loss coefficient. water at

  An airplane was moving with a velocity equal to 300mph when

an airplane was moving with a velocity equal to 300mph when the velocity was increased with uniform acceleration to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd