What it the distance after adjusting for sag

Assignment Help Civil Engineering
Reference no: EM13555102

1.From right to left, a beam has a pin support on the left end, and a roller support at length 2L, and the rest of the beam hangs off of to the right of the roller support for length L, the entire length of the beam 3L has a uniformly distributed load of w. Draw the V and M diagrams.

2.A 245 m ship has a displacement of 3x10^8N,and the area defined by the waterline is 3550m^2.will the ship take more or less draft when steaming from salt water to fresh water? How much will it settle or rise?

3.A 200ft tape is hung in catenary. It is supported at the 80ft mark the tension is 20lbf and the weight of the tape is 3 lbf 5 0z. The measured distance is 187.01 what it the distance after adjusting for sag?

4.A force is specified by the vector F  120i  160j  80k lb. Calculate the angles made by F with the posi- tive x-, y-, and z-axes

Reference no: EM13555102

Questions Cloud

Determine two possible angles theta at which this : A fireman is standing on a hoist and sprays water at a fire. the fire is 35 ft in the x direction and 20ft downward in the y direction. the water flows at 65 ft/s. determine two possible angles theta at which this can be done. assume the angle below ..
Find steady state concentration of pollatant in the lake : A lake with constant volume 10x10^6 m^3 is fed by pollation free stream with flow rate 50m^3/s. fator dumps 5m^3/s of nonconservative waste with concentration
Computer the volume of fill that will be produced : A 3 ft deep cut is to be made across an entire 2.5-acre site. The average unit weight of this soil is 118 lb/ft^3, and the average moisture content is 9.6%.
Determine the magnitude of the reaction force exerted at b : The image is of a plane who's wheels are spread apart by 12 ft and on the ground. The left wheel being point A and the right wheel being point B. It also has an arrow around the front propeller in the clockwise direction.
What it the distance after adjusting for sag : A 200ft tape is hung in catenary. It is supported at the 80ft mark the tension is 20lbf and the weight of the tape is 3 lbf 5 0z. The measured distance is 187.01 what it the distance after adjusting for sag?
What will be the concentration of tce in the aqueous phase : The dimensionless henry's constant for TCE at 25 degrees celsius is 0.4. A sealed glass vial is prepared that has an air volum of 4mL overlying an aquesous volume of 36mL. TCE is added to the aqueous phase so that initally
Determine which driver will be the first to displace later : Vehicles A and B are traveling toward each other in the opposing lanes on a straight segment of a two-lane highway at 35 and 40 mph respectively. If the critical rates of angular change of the two drivers are 0.0065 and 0.0055 rad/s, determine
Determine whether it has an fcc or bcc crystal structure : Rhodium has an atomic radius of 0.1345nm and a density of 12.41g/cm^3. determine whether it has an FCC or BCC crystal structure.
Calculate the maximum and minimum possible dry unit weights : For a sand, the maximum and minimum possible void ratios were determined to be 0.94 and 0.33 respectfully. Find the moist unit weight of sand in lb/ft^3compacted in the field at a relative density of 60%and moisture content of 10%Given Gs=2.65

Reviews

Write a Review

Civil Engineering Questions & Answers

  Under what situation shall engineers use jacking at one end

Sometimes the side of concrete bridges is observed to turn black in colour. What is the reason for this phenomenon? In prestressing work, if more than one wire or strand is included in the same duct, why should all wires/strands be stressed at the sa..

  Please give the numberal value of the following strengths

We have a small wood deck, 8' by 8' This deckshould only have a max of five adults on it. Oneside of deck is attached to the wall of the house, and out fromthis wall is two post six feet from the wall.   Problem is the load bearing strength of the be..

  Probelm related to when object is thrown downward

An object is thrown downward from a 150-ft cliff with a velocity of 45m/hr so that it makes an angle of 60° with vertical face of the cliff.

  Which method would be most likely to have the conductivity

If an analysis is made of the hydraulic conductivity of a site using permeameter tests of core samples, slug tests of monitoring wells, and pumping tests of production wells, it is often observed that the hydraulic conductivity as measured by each..

  Determine minimum surge tank size for max allowable height

A hydroelectricity plant is supplied from a resevoir via a pipeline 2km long and 2.5m in diameter. The pipeline terminates at the downstream end at in a control valve. Determine the minimum surge tank size if the max allowable height

  Were the rumble strips effective in reducing average speeds

A before-and after speed study was conducted to determine the effectiveness of a series of rumble strips installed approaching a toll plaza to reduce approach speeds to 40 mi/h.

  Determine the room temperature when the student comes back

A NCSU student turned on his/her 150 W fan inside his/her room, 4m * 6m * 6m, before going to class in the morning of a summer day, excepting to find his/her room cooler when he/she returns at night.

  Thermal conductivities of aluminum and copper

The aluminum end and the copper end are maintained at temperatures of 50°C and 260°C, respectively. The thermal conductivities of aluminum and copper are 205 and 385 W/m · K, respectively. The temperature of the aluminum-copper junction in the rod..

  What was involved in the first far-reaching

what was involved in the first far-reaching, comprehensive study of Earth's oceans?

  How long would figure soil will take to reach contamination

The local engineer concludes that, since the oil must have been destroyed by the soil microorganisms at a rate of 20 mg/kg each year, in one more year the site will be free of all contamination. a. Is this a good assumption

  What is the maximum grade the vehicle could ascend

A 2500-lb car (CD = 0.35, Af = 25 ft^2, and ? = 0.002378 slugs/ft^3) has 14-inch-radius wheels, a drivetrain efficiency of 90%, an overall gear reduction ratio of 3.2 to 1, and drive axle slippage of 3.5%.

  Discuss if you are going or not to stabilize the slope –why

Given that that there is no budget to built any type of artificial protection enclosure or retention wall but you still have some allowance for using earthmoving equipment, which of the techniques discussed in class would appropriate in case slope pr..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd