What is your estimate of the cumulative average hours

Assignment Help Mechanical Engineering
Reference no: EM131178522

The structural engineering design section within the engineering department of a regional electrical utility corporation has developed several standard designs for a group of similar transmission line towers.

The detailed design for each tower is based on one of the standard designs. A transmission line project involving 50 towers has been approved. The estimated number of engineering hours needed to accomplish the first detailed tower design is 126. Assuming a 95% learning curve,

What is your estimate of the number of engineering hours needed to design the eighth tower and to design the last tower in the project?

What is your estimate of the cumulative average hours required for the first five designs?

Reference no: EM131178522

Questions Cloud

Give a brief job description : List 5 different types of careers in the cyber security field. Give a brief job description.
Why is it unethical to share copyrighted files : Why is it unethical to share copyrighted files with your friends? Which of the following can be used to select the entire document?
Evaluate your model utilizing the general criteria provided : Evaluate your model utilizing the general criteria provided in the text. You are required to use at least two outside resources to support your position.
What do you understand by the term booting : Which device can understand difference between data and programs? What do you understand by the term booting?
What is your estimate of the cumulative average hours : The structural engineering design section within the engineering department of a regional electrical utility corporation has developed several standard designs for a group of similar transmission line towers.
What will the firm unlevered beta be after refinancing : The firm’s unlevered (asset) beta is 0.77. Book and market values are equal. The firm has $40 million of debt, 5% interest rate, and $60 million of equity outstanding. The market risk premium is 4%.The firm is considering refinancing by selling bonds..
Discuss the purpose of a grand jury issuing a true bill : Explain why a grand jury is used rather than the prosecutor simply issuing a criminal charge. Discuss the purpose of a grand jury issuing a true bill (criminal charge) or not.
Advantage of using a spread sheet : On an excel sheet the active cell is indicated by? What is the advantage of using a spread sheet?
Which is the best describes the dual nature of light : The "speed of light" (c) refers to the speed of all electromagnetic waves under what conditions? Which of the following characteristics of an object would allow no light to pass through?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  How to make a mouse trap powered vehicle

I need help to write the procedure about how to make a Mouse Trap Powered Vehicle.(then I will finish that with my team). And you also need to help me write a lab report too. I am sure to get a good procedure and lab report. Read the instruction w..

  Determine the rate of evaporation

In a gas-fired boiler, water is boiled at 150°C by hot gases flowing through 50-m-long, 5-cm-outer-diameter mechanicallypolished stainless steel pipes submerged in water.

  Density and volume flow rate of nitrogen at the exit

Nitrogen flows steadily through a pipe with a constant cross-section area of 6cm^2. The nitrogen enters the pipe at 500 kPa and 50 degrees Celsius with a velocity of 15m/s. The nitrogen leaves the pipe at 200 kPa and 25 degrees Celsius. Assume that t..

  Heat tansfer please find attached some work i need help

please find attached some work i need help with. i have also attached the appendix which the work says is required to

  For each process of a closed system show the initial and

for each process of a closed system show the initial and final states on a properly-labeled t-s diagram evaluate the

  Determine the air exit temperature

Air with a mass flow rate of 1.5 kg/sec and temperature of 400 K flows through a horizontal duct of an air heater. If 36 kJ/sec of heat is added to the flow, determine the air exit temperature. Assume ideal gas and neglect any change in pressure and ..

  Determine the maximum load that can be applied for the

a plate 50 mm wide and 15 mm thick is loaded in tension. the plate is made from steel with yield strength of 1500 mpa

  Consider a finite wing with an aspect ratio of 7 the

consider a finite wing with an aspect ratio of 7 the airfoil section of the wing is a symmetric airfoil with an

  Manometer is connected to a tank of unknown pressure

One side of a manometer is connected to a tank of unknown pressure while the other side is open to the atmosphere. The manometer is filled with water and the height of the water is 18.7 cm higher on the tank side than on the atmospheric side. If the ..

  What is the total heat loss

A vertical run of copper tubing, 5 mm in diameter and 20 cm long, carries condensation vapor at 60?C through 27?C air. What is the total heat loss?

  Calculate the force required in direct extrusion

Calculate the force required in direct extrusion of 1100-O aluminum from a diameter of 6 in. to 2 in. Assume that the redundant work is 30% of the ideal work of deformation, and the friction work is 25% of the total work of deformation.

  What is the pressure at the bottom of the mariana trench at

a sea water is often modeled as an incompressible fluid with a density of 1025 kgm3.what is the pressure at the bottom

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd