What is the water content of the material when saturated

Assignment Help Civil Engineering
Reference no: EM13562669

1.A sample of natural glacial till was taken from below the groundwater table. The water content was found to be 52%. Estimate the wet density, dry density, buoyant density, porosity, and void ratio. Clearly state any necessary assumptions.

2.The dry density of a compacted sand is 1.87 Mg/m^3 and the density of the solids is 2.67 Mg/m^3. What is the water content of the material when saturated. Include a phase diagram.

Reference no: EM13562669

Questions Cloud

Determine how much he will weigh on the spring scale : An undisturbed chunk of soil has a wet weight of 62 lb and a volume of 0.56 ft3. When dried out in an oven, the soil weighs 50 lb. If the specific gravity of soilds is found to be 2.64
Find the dry unit weight void ratio and degree : The area of a parking lot is calculated to be 5,474 ft^2 with an estimated standard deviation of 2 ft^2. What is the maximum anticipated error? there is a 90% chance that the error range will be what?
How fast was the car traveling before applying the brakes : You have been hired to review an accident scene where a vehicle hit a light pole at the intersection of main and 5th. The vehicle was estimated to hit the light pole at 30 mph.
At what point on the expressway should the motorist step on : A motorist traveling at 55 mph on an expressway intendeds to leave the expressway using an exit ramp with a maximum allowable speed of 30 mph. At what point on the expressway
What is the water content of the material when saturated : The dry density of a compacted sand is 1.87 Mg/m^3 and the density of the solids is 2.67 Mg/m^3. What is the water content of the material when saturated. Include a phase diagram.
Calculate the wet unit weight in pounds per cubic feet : A gray silty clay (CL) is sampled from a depth of 12.5 feet. The "moist" soil was extruded ffrom a 6-inch high brass liner with an inside diameter of 2.83 inches and weighed 777 grams.
Find the height and the width of the triangular soil bank : A ditch having a cross-sectional area of 50 square feet is being excavated in common earth. The soil’s angle of repose is 35° and its swell is 25%. Find the height and the width of the triangular soil bank that will result from the trench excavation
What is the volume of the required soil excavated : Soil is excavated from a borrow to construct an embankment with a net volume of 50,000 cy. This is performed by compacting 12-in layers of the soil to a dry weight of 110 pcf at a moisture content of 18%.
What is the pulling force in lbs to be applied for one of : Two steel plates were constructed in warm weather. Due to temperature change, a 1/32" hole mismatching occurred. What is the pulling force, in lbs, to be applied for one of the plates to match the two holes The plate length is 3 ft (from the left end..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determne the diameter of the tube at a uniform rate

A 25 mm diameter steel cylinder falls under its own weight at a uniform rate of 0.1 m/s inside a tube of slightly larger diameter. Castor oil of viscosity 0.25 N.s/m2 fills the spacing between the tube and the cylinder.

  What percent removal of particles would be expected

if the settling velocity of a particle is 2.80 mm/s and the overflow rate of an up flow clarifier is 0.560 cm/s, what percent of the particles are retained in the clarifier. If the flow rate of this problem is doubled

  What minimum size pipe laid on the respective minimum slope

A MH at an intersection has an inflow from three 8-inch PVC (n = 0.01) sanitary sewer pipes laid at minimum slope converging at an intersection and one pipe taking the flow from those three further downstream.

  Draw a neat and clearly annotated sketch of the curve

Given the stationing in meters as (4+56) for the PC of a horizontal curve of radius R=1200 meters and angle I=22°. The azimuth of the line PC to PI as AzPC-PI = 155° 30'. A point P is to be located on the curve at stationing of 7+00. Do the following

  Find the minimum dimension of the other side

The modulus of elasticity of the wood is 13GPa. If one side of the column is 25cm across, find the minimum dimension of the other side to keep the column's deformatin under 1.3 mm

  How high can students climb just before the pole buckles

Assuming the center of gravity of the student aligns with the axis of the pole and the pole has an elastic behabior, how high can they climb (in meters, m) just before the pole buckles

  Determine the relationship between the discharge and the

A fluid of density rho flows steadily downward between the two vertical, infinite, parallel plates. The flow is fully developed and laminar. Make use of the Navier Stokes equation to.

  Determine the minimum force p to prevent a 30kg rod

Determine the minimum force P to prevent a 30kg rod AB from sliding on a wall. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is Us=0.2.

  For what reason would need to use darcys law in foeld

FOR WHAT REASON WOULD YOU NEED TO USE DARCY'S LAW IN THE FOELD RATHER THAN IN THE LABORATORY

  Determine what is the outlet air temperature

A total of 13,610 kg/h of air at 1 atm abs pressure and 15.6C is to be heated by passing over a bank of tubes in which steam at 100C is condensing. The tubes are 12.7mm OD, 0.61 m long, and arranged in-line in a square pattern with Sp=Sn= 19.05mm.

  Obtain the dimensionless groups that charactrize the problem

The power loss, p , in a journal bearing depends on length, L; diameter, D; clearance, c; and rotational speed, w. You also have to worry about lubricant viscosity, density, and pressure. Obtain the dimensionless groups that charactrize this probl..

  Calculate the compacted cubic yards per hour with a drum

Calculate the compacted cubic yards per hour if a compactor with a 5-ft drum width travels at 3 mph over a 10-in. lift of aggregate base course with 4 passes required to meet density specifications under average operating conditions.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd