Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Figure P2-1 shows a three-phase power system with two loads. The Δ-connected generator is producing a line voltage of 480 V, and the line impedance is 0.09 + j0.16Ω. Load 1 is Y-connected, with a phase impedance of 2.5Ð36.87° Ω and load 2 is Δ-connected, with a phase impedance of 5<-20° Ω.
(a) What is the line voltage of the two loads?
(b) What is the voltage drop on the transmission lines?
(c) Find the real and reactive powers supplied to each load.
(d) Find the real and reactive power losses in the transmission line.
(e) Find the real power, reactive power, and power factor supplied by the generator.
A 1.2 MW wind turbine has a rotor diameter of 64 m. the turbine operates in an area with an average wind velocity of 7.5 m/s and the air density of 1.18 kg/m^3. the turbine power coefficient including the unit efficiency is 42.8 percent.
The inferred absolute temperature for copper is -243.5C. If the resistance of a copper wire is 10 ohms at 25C, what is its resistance at 200C
NATIONAL NZ ELECTRICITY TRANSMISSION GRID - Erection of additional Transmission Lines
A circuit contains a known resistance of 2.4 kO, and an unknown inductance. a) When a 12-V battery is connected, what is the current in the circuit a long time after the switch is closed
A single phase full bridge inverter feds power at 50Hz to RLC load with r=5 ohms , l=0.3H and C=50μF. The dc input voltage is 220volts. (a) Find an expression for load current up to fifth harmonic
Calculate the numerical value of the mutual capacitance of a square parallel plate capacitor whose dimensions are 1 mm X 1 mm if the two plates are separated by a distance of 2 mm. The relative dielectric constant of the material between the two p..
Excitation is provided by a 140-turn, 30 ohm coil. Determine the voltage required to establish a flux density of 1.56T. The reluctance of the magnetic circuit, when operating at this flux density is 768 A-t/Wb.
A 190-F capacitance is initially charged to 1190V . At t = 0, it is connected to a 1-k resistance. a) At what time t2 has 50 percent of the initial energy stored in the capacitance been dissipated in the resistance
A typical commercial FM broadcast signal starts out at an effective power level around 100 KW (+80 dBm). How much of that FM signal power finds its way into the clock radio on your nightstand, or the radio in your car's dash
design a resonance circuit with following specifications: L = 10 mH, RL = 4W, Imax = 200 mA, fs = 10kHz, Q = 20. That is, determine the required R, C, and supply Voltage E. For R and C, use the closest standard values.
How much steam is required for each pound mass of entering acid, and what is the concentration of the hot acid?
1. What are the signals common to both minimum and maximum mode of 8088 microprocessor 2. What does status code S4S3 =01 mean in terms of the memory segment being accessed 3. What frequency crystals must be connectedbetween the X1 and X2 inputs of th..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd