User Account

All Pages

What is the void fraction if the cubes are replaced with

Assignment Help Mechanical Engineering
Reference no: EM13629556

A packed bed is composed of cubes 0.02 m on a side and the bulk density of the packed bed is 980 kg/m3. The density of the solid cubes is 1500 kg/m3.

a.) Calculate the void fraction (ε) and effective diameter (Dp).

b.) What is the void fraction if the cubes are replaced with cylinders that have a diameter 0.02 m and a height 0.02 m, all other parameters remaining the same?

Reference no: EM13629556

Questions Cloud

Assuming the car accelerates from 0 to 59 mph at a constant : the 2007 bmw z4 coupe 3.0si can accelerate from 0 to 59 mph in 5 s and its maximum speed is 152 mph. assuming the car
The star vega has a measured angular diameter of 324 mas : the star vega has a measured angular diameter of 3.24 mas milliarcseconds and a flux of 2.84 x 10-8 wm2. its distance
47of americans when surveyed by a gallup poll felt that : 47of americans when surveyed by a gallup poll felt that having a gun in the home made them safer than having no gun.
Steam at 40c condenses on the outside of a 5-m-long : steam at 40?c condenses on the outside of a 5-m-long 3-cm-diameter thin horizontal copper tube by cooling water that
What is the void fraction if the cubes are replaced with : a packed bed is composed of cubes 0.02 m on a side and the bulk density of the packed bed is 980 kgm3. the density of
Air at 15 degc and atmospheric pressure is forced over the : water at the rate of 0.8 kgs at 93 degc is forced through a 5 cm id copper tube at a suitable velocity. the wall
After 7 seconds the speed of the automobile is 60 mph use : a 2000 lbm automobile is driving down a level road at 70 mph. the engine is disengaged and the automobile is allowed to
Steam enters an adiabatic turbine at 2 mpa 300c and exits : steam enters an adiabatic turbine at 2 mpa 300c and exits at 50 kpa. the mass flow rate through the turbine is 2 kgs
What kind of data analysis method is more appropriate why : three samples of 9 members each were selected representing urban suburban and rural residents to evaluate their

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The refrigerant leaves the condenser at 07 mpa 26 degc

consider a non-ideal vapor-compression cycle where refrigerant 134a flows at a rate of 0.05 kgs. the refrigerant enters

  Find the transfer function for the impulse response

Find the transfer function for the following impulse response

  The vertical load on the hook is 1000 lb draw the

the vertical load on the hook is 1000 lb. draw the appropriate free-body diagrams and determine the maximum average

  Steam enters a well-insulated nozzle at 300lbfin2 600

steam enters a well-insulated nozzle at 300lbfin2 600 degrees f with a velocity of 100 fts and exits at 40 lbfin2 with

  Ignoring the heat transfer changes in potential energy and

hot air steadily enters a gas turbine at 5 bar 900 k and exits at 1 bar 600 k and a velocity of 100 ms. the mass flow

  How is diffusion time related to diffusion temperature

how is diffusion time related to diffusion temperature for the case where the concentration at some distance into an

  Each glass bottle has an empty dry mass of 120 grams based

all makers of beverages such as breweries wineries and soda makers must wash bottles before filling. a new beverage

  The chute is deployed is -0003 v2 speed v in feet per

the 230000 lb space shuttle orbiter touches down at about 220 mihr. at 200 mihr its drag parachute deploys. at 35 mihr

  What is percentage increase in the force that is required

the hydraulic jack shown below consists of a master cylinder with a diameter of 60mm and a lifting or slave cylinder

  Estimate the design-stage uncertainty in determining the

estimate the design-stage uncertainty in determining the voltage drop across an electric heating element. the heater

  During a race the dirt bike was observed to leap up off the

during a race the dirt bike was observed to leap up off the small hill at a at an angle of 60o from the horizontal. if

  Determine the maximum shear stress in the beam

If the wide-flange beam is subjected to a share of V = 25 kip, determine the maximum shear stress in the beam.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd