Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A 5.88-g bullet is moving horizontally with a velocity of +340 m/s, where the sign + indicates that it is moving to the right (see part a of the drawing). The bullet is approaching two blocks resting on a horizontal frictionless surface. Air resistance is negligible. The bullet passes completely through the first block (an inelastic collision) and embeds itself in the second one, as indicated in part b. Note that both blocks are moving after the collision with the bullet. The mass of the first block is 1247 g, and its velocity is +0.645 m/s after the bullet passes through it. The mass of the second block is 1534 g.
(a) What is the velocity of the second block after the bullet imbeds itself?
(b) Find the ratio of the total kinetic energy after the collision to that before the collision.
A PPL multiplier transmitter is to operate with a 915 MHz output. With a divide factor of 64, what value of crystal is needed
Design a Miller integrator with a time constant of 0.1 s and an input resistance of 100 k ohm. A dc voltage of -1 volt is applied at the input at time 0, at which moment vO = -10 V. How long does it take the output to reach 0 V to +10 V
The messages being sent are 2 milliseconds long. Computer A starts sending a message on the bus; 250 microseconds later, Computer B starts to send a message, and 250 microseconds after that, Computer C starts to send a message.
The duration of a cellular call is an exponential random variable with expected value of 3 minutes. A subscriber makes 120 calls each month. Use the central limit theorem to estimate the probability that the subscriber uses at least 400 minutes.
You are required to determine that this next generation transmission system will require a spectral efficiency of 5 bits/sec per Hertz.
Design an adder that computes the sum of four 8-bit numbers, using 8-bit carryripple adders. Use a basic 8-bit carry-ripple adder as a building block for the design.
For an RC circuit with a time constant of 1.0ms and assuming switch was closed at t=0, i) What is the time for the voltage across resistor to equal 10% of its initial value ii) What is the time for the voltage acro..
Design a full-wave bridge rectifier circuit to deliver 10 volts de with less than 0.1 volt (pp) ripple into a load draWing up to 10mA. Choose the appropriate ac input voltage. assuming 0.6 volt diode drops.
Convert the value: $2103.25 using an IEEE standard 4 byte (32 bit) float floating point number representation. Identify every bit of the 32 bit number holding this record by first converting the number 2103.25 from decimal to binary
An odd parity circuit with 2^n inputs can be built with 2^n-1 XOR gates. Describe two different structures for this circuit, one of which gives minimum worst-case input to output propagation delay and the other of which gives a maximum.
Two point charges q1 = 2.0 C and q2 = 1.0 are fixed in a plane at the positions given by the Cartesian coordinates shown in the figure at right. Consider that they are in a vacuum, where ko = 9.0 × 109 N.m2/C2.
Design a 2-bit counter that, when f = 1, counts in the repeating sequence: 0, 2, 3, and when f = 0, counts in the reverse direction. Use T flip-flops. (a) Construct a state diagram or state table.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd