What is the velocity of the collar

Assignment Help Mechanical Engineering
Reference no: EM13216727

The system is at rest in the position shown, with the 12-lb collar A resting on the spring (k = 20 lb/ft), when a constant 30-lb force is applied to the cable. What is the velocity of the collar when it has risen 1 ft? The collar is attached to the spring. Use the work-energy method.

Reference no: EM13216727

Questions Cloud

Calculate average velocity and mass flow rate of air : wall temperature needed for the runner to cylinder #3, such that the cylinder air inlet temperature is the same as that in cylinder #1. Runner length for cylinder #3 is 15 cm.
Explain circumstances where osha : Explain circumstances where OSHA would be able to enter and inspect a worksite without obtaining a warrant or the employer’s permission.
Define concept and not violate any federal legislation : Define Comparable Worth and explain how companies attempt to compensate their employees based on such a concept and not violate any federal legislation.
Design experiment to test whether drinking alcohol influence : Design an experiment to test whether drinking alcohol influences people's tendency to become socially aggressive. Be sure to specify your experimental hypothesis and identify your dependent and independent variables, as well as your experimental and ..
What is the velocity of the collar : The system is at rest in the position shown, with the 12-lb collar A resting on the spring (k = 20 lb/ft), when a constant 30-lb force is applied to the cable. What is the velocity of the collar when it has risen 1 ft? The collar is attached to th..
Consider a metal single crystal oriented : Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 43.1
Elements of an effective medical office financial policy : What are the basic elements of an effective medical office financial policy? In what ways do medical office procedures support financial policies? What are the consequences when office procedures do not support the financial
Find the tension in ropes a and b : a 100 pound ball is suspended from a wall by a rope that is pulled asided by a horizontal rope B and held so that rope A makes a angle of 30 degrees with the vertical wall. Find the tension in ropes A and B?
Implementation of project portfolio management : Implementation of project portfolio management should be initiated by the top managers, executive and high level managers should be committed to the portfolio management system first and then influence the team to be committed to the system.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd