What is the velocity of propagation of the cable

Assignment Help Electrical Engineering

Reference no: EM13228521

1. A lossless transmission has a shunt capacitance of 20 pF/ft and a series inductance of 180 nH/ft. Its surge impedance is
A. 36 . C. 95 .
B. 80 . D. 300 .

2. What is the delay introduced by 1 foot of the cable described in question 1?
A. 1.9 ns C. 6.0 ns
B. 3.6 ns D. 9.0 ns

3. What is the velocity of propagation of the cable described in question 1?
A. 5.26 108 ft/sec C. 1.9 109 ft/sec
B. 5.26 108 m/sec D. 1.9 10-9 ft/sec

4. A slotted line is used to measure the voltage maximums and voltage minimums on a transmission line with a characteristic impedance of 50 . The voltage maximum is measured as 7.5 V and the minimum is 5 V. The line is terminated with a purely resistive load. What is the load impedance?
A. 5 C. 25
B. 12 D. 75

5. The transmission line input impedance is equal to its characteristic impedance when
A. it's lossless.
B. it has finite length.
C. it's nonresonant.
D. its capacitance is equal to its inductance.

6. A TDR is being used to analyze a transmission line problem. The oscilloscope display shows a positive-going voltage step with a DC level equal to twice the input voltage at 2 ms. What can be determined from this display?
A. There's a short circuit at a point 2ms Vp from the source.
B. There's a short circuit at a point 1ms Vp from the source.
C. There's an open circuit at a point 2ms Vp from the source.
D. There's an open circuit at a point 1ms Vp from the source.

7. A short-circuited line less than /4 in length is the same as a(n)
A. capacitor.
B. inductor.
C. quarter-wave matching transformer.
D. stub tuner.

8. Television sets generally have two screw terminals connected to an internal two-wire transmission line at their antenna input. If coax is to be connected to the TV, how should it be done?
A. Through a quarter-wave transformer
B. Through a balun transformer
C. Connect each conductor to one of the screws
D. With a double-stub tuner

9. A 300 transmission line is terminated with an antenna that presents a (450 - j 600 ) load impedance. What is the normalized load admittance?
A. 0.002 + j 0.0016 C. 1.5 - j 2
B. 0.24 + j 0.32 D. 1 + j 1.7

10. How far from the load should a short-circuit stub be placed to match the load in question 9?
A. 0.07 C. 0.052
B. 0.25 D. 0.130

11. How long should the stub in question 9 be?
A. 0.085 C. 0.334
B. 0.18 D. 0.601

12. What is the VSWR before matching at the load described in question 9?
A. 0.38 C. 1.7
B. 1.00 D. 4.62

13. What is the VSWR after matching at the input of the transmission line in question 9?
A. 1.7 C. 0.55
B. 1 D. 0.38

14. An open-circuited line is seldom used as a tuning component. Why?
A. Open circuits are hard to construct.
B. Open-circuit tuning uses more cable than short-circuit tuning.
C. Open circuits tend to radiate.
D. Open circuits create an unbalanced condition.

15. Increasing the separation of the conductors in a two-wire transmission line will
A. decrease Z0.
B. increase Z0.
C. increase e (dielectric constant).
D. decrease e (dielectric constant).

16. A short-circuited line greater than /4 long appears as a(n)
A. capacitor. C. open circuit.
B. inductor. D. resistance.

17. A shorted stub is used instead of an inductor in tuners because of
A. cost considerations. C. superior selectivity.
B. space considerations. D. broader bandwidth.

18. A load of 100 + j50 is to be matched to a 50 transmission line using a /4 matching section. How much transmission line is needed between the load and the /4 matching section?
A. 0.038 C. 0.28
B. 0.138 D. 0.78

19. What should the characteristic impedance of the matching section be?
A. 130 C. 81
B. 120 D. 50

20. In high-power applications, excessive losses can cause poor performance of the system because
A. the energy is reradiated.
B. energy is lost to magnetic coupling.
C. there's too much resistance between the conductors.
D. transmitter energy is converted to heat.

21. A twisted-pair transmission line is suffering from crosstalk interference. What can be done to improve the performance?
A. Twist the cable tighter.
B. Remove some twists from the cable.
C. Increase the dielectric constant of the cable.
D. Use larger conductors.

22. Dielectric losses occur when
A. the conductor separation is too great.
B. the conductor separation is too small.
C. currents flow from one conductor to the other through the dielectric.
D. the cable is unshielded.

Reference no: EM13228521

Questions Cloud

Explain how much heat was released : The combustion of propane illustrated by the following reaction releases 2428 KJ per mole of reaction. A sample of propane is burned at 59 degrees celsius and 746 mm Hg. The process produces 39.7 L of CO2(g). How much heat was released?

Explain the nurses role in the evaluation and management : Explain the nurse's role in the evaluation and management of selected diseases and disorders.

Explain acetate buffer with acetic acid and sodium acetate : Describe three ways to could make and acetic acid/acetate buffer with acetic acid, sodium acetate, deionized water, a solution of hydrochloric acid and a solution of sodium hydroxide.

Decision on accepting additional business : Decision on Accepting Additional Business

What is the velocity of propagation of the cable : A slotted line is used to measure the voltage maximums and voltage minimums on a transmission line with a characteristic impedance of 50 . The voltage maximum is measured as 7.5 V and the minimum is 5 V. The line is terminated with a purely resist..

Paper on the french commune of 1971 and marxism : I need to write a paper on the French Commune of 1971 and Marxism. Can you help me write an introduction and give me themes to write about?

Explain what would be the best acid or base system : Suppose you wanted to make a pH=4.25buffer. What would be the best acid/base system: acetic acid/acetate or lactic acid/lactate? THe Ka of lactic acid is 8.32x10(exponent -4). Throughly explain your reasoning.

Statements regarding project crashing : The normal time to complete this activity is 8 days and crash time is 4 days. If this activity is crashed by 2 days it will cost an additional - statements regarding project crashing

Explain how many grams of dry nh4cl need to ammonia : How many grams of dry NH4Cl need to be added to 1.50 L of a 0.300 M solution of ammonia, NH3, to prepare a buffer solution that has a ph of 8.73? pkb for ammonia is 1.8X10^-5.

User Account

All Pages