What is the velocity of gas 1

Assignment Help Mechanical Engineering
Reference no: EM131200400

Two gases flow into separate ducts and merge into a single large duct. Gas 1 has a density of 1.5kg/m^3 and flows into a duct with an area 0.25m^3. a. If gas 2 has a density of .8 kg/m^3 and volume flow rate of 2.5 m^3/s what is the velocity of gas 1?

Reference no: EM131200400

Questions Cloud

President of the airline and complain : Assume you were an infortunate passenger on a flight that never left the airport. After sitting on the plance for three hours, you deplaned, you waited two more hours, and the flight was cancelled. You decide to write to the president of the air..
Estimate the net energy transfer from the fluid as work : 1. Inlet Exit Pressure 1.15 MPa 0.05MPa Velocity 30 m/sec 15.5 m/sec Height above datum 10 m 2m If the volume flow rate of the fluid is 40 m3 /s, estimate the net energy transfer from the fluid as work.
What are the differences between databases : What are the differences between databases, data warehouses, and data mining? When would you use one over another?
What is van dykes after tax yield on the preferred stock : What is Van Dyke's after-tax yield on the preferred stock?- What is the after-tax return on the preferred stock, assuming a 70% dividend exclusion?
What is the velocity of gas 1 : Two gases flow into separate ducts and merge into a single large duct. Gas 1 has a density of 1.5kg/m^3 and flows into a duct with an area 0.25m^3. a. If gas 2 has a density of .8 kg/m^3 and volume flow rate of 2.5 m^3/s what is the velocity of ga..
What are the three primary data gathering methods : What are the three primary data gathering methods? What method would you use if you were gathering data on a movie studio? A grocery retailer? A pharmaceutical company? Why did you select that method for each of the types of companies identified o..
Purpose and successful application of different types : Successful interviews are carefully planned and executed events. Discuss the purpose and successful application of different types of interview environments (traditional, panel or committee, group, telephone, etc.) and questions (behavioral, situa..
What would you expect her rate of breathing at 18,000 ft : what would you expect her rate of breathing at 18,000 ft (5486 m) to be? Use standard atmospheric conditions.
Effective tool in the selection of qualified candidates : Pre-employment testing can be an effective tool in the selection of qualified candidates. Testing can include, but is not limited to the following areas: personality, talent assessment, job task proficiency and productivity, physical ability, drug..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd