What is the velocity of flow into the pipe line what is the

Assignment Help Mechanical Engineering
Reference no: EM13628069

Consider the following gas well drilled 2,000 meters vertically with a (essentially) horizontal leg of 200 meters length. The entire well is cased (closed) except for a 10 cm long cylindrical permeable plug at the end of the horizontal leg. The vertical section is 10 cm in diameter, the horizontal leg 10 cm in diameter. At the top of the well there is a valve and pressure meter. Next is a porous filter (10 cm in diameter and 10 cm in length) with a pressure meter on the filter output which feeds into a 10 cm diameter pipe line.

Assume ideal gas behavior and constant identical temperatures. Given the following values: P1=190 atmospheres, P2=10 atmospheres, k=10mD, µ=.01cp a)What is the volume flow rate into the pipe line? b)What is the volume flow rate into the filter? c) What is the velocity of flow into the pipe line? d)What is the velocity of flow into the filter? e) If the density of the pipe line gas is .0064 gms/cm^3 what is the density of the gas at the filter input?

Reference no: EM13628069

Questions Cloud

Determine the pressure at which condensation first occurs : steam is contained in a closed rigid container. initially the pressure and the temperature are 1.4 mpa and 250degc
A circular shaft of 120-mm diameter is subjected to end : a circular shaft of 120-mm diameter is subjected to end loads p 45 kn m 4 kn.m and t 11.2 kn.m. what is the factor
A toroidal selenoid has inner radio r1 150 cm and outer : a toroidal selenoid has inner radio r1 15.0 cm and outer radius r2 18.0 cm. the selenoid has 250 turn and carries a
Consider a normal population with u42 and standard : consider a normal population with u42 and standard deviation 5.4. calculate the z-score for an x bar of 49 from a
What is the velocity of flow into the pipe line what is the : consider the following gas well drilled 2000 meters vertically with a essentially horizontal leg of 200 meters length.
A particle moving along the x axis in simple harmonic : a particle moving along the x axis in simple harmonic motion starts from its equilibrium position the origin at t 0
What is the probability that a randomly chosen 10-card hand : what is the probability that a randomly chosen 10-card hand has exactly three three-of-a-kinds and no
In addition to driving the air compressor the turbine : an adiabatic compressor compresses air from atmospheric pressure and 70 degf at a rate of 10000 acfm actual cubic feet
Determine the net force acting on block a using newtons 2nd : using the fact that the tension in the rope must remain constant in all sections of the rope calculate the total force

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd