User Account

All Pages

What is the velocity in ms through the orifice

Assignment Help Mechanical Engineering
Reference no: EM13711767

A 3cm inside diameter pipe has a 1 cm orifice installed in it. The pipe is flowing 150g/s water. What is the velocity in m/s through the orifice? What is the Reynolds number? The orifice Coefficient, Cv? What is the pressure drop in Pa?

Reference no: EM13711767

Questions Cloud

Determine the time required by a diesel-electric locomotive : Determine the time required by a diesel-electric locomotive, which produces a constant drawbar pull of 60,000 lb, to increase the speed of an 1800 ton freight train from 20 mi/hr to 30 mi/hr up to 1-percent grade. Train resistance is 10 lb per ton.
Use simulink to do the simulations of the step responses : Write down the transfer function of a third-order system with unity steady-state gain which has a real pole at s = -1 and a pair of complex poles at s = -1 +- ja. Simulate the open-loop step response of the system for 'a' values of 1, 2, 4, and 10, a..
A correct statement regarding transactions : 1. According to double-entry accounting, which of the following is a correct statement regarding transactions? Each transaction must increase an asset and a liability. Purchasing supplies on account is shown by an increase on the left side of the T-..
What is his quarterly payment : Bill borrowed $10,000 to be repaid in quarterly instalments over the next 5 years. The interest rate he is being charged is 10.26% per year compounded quarterly. What is his quarterly payment? Give answer without $ sign with 2 decimal place precision..
What is the velocity in ms through the orifice : A 3cm inside diameter pipe has a 1 cm orifice installed in it. The pipe is flowing 150g/s water. What is the velocity in m/s through the orifice? What is the Reynolds number? The orifice Coefficient, Cv? What is the pressure drop in Pa?
What is the entropy change of the flame : You are boiling a kettle of water over a propane stove that is supplying a uniforma amount of heat. You note that it takes 3 minutes to heat water which is initially at 20C to its boiling point. Just as the water begins to boil, you receive a phone c..
Determine the force required to hold the nozzle : Water (at 15 C) flows out of a nozzle that is attached to a garden hose. The volume flow rate is through this nozzle at a rate of 25 x 10-5 m3/s, which discharges into the atmosphere. The diameter of the garden hose is 1.5 cm, while the diameter of t..
Assume a fire truck can shoot water from an onboard tank : Assume a fire truck can shoot water from an onboard tank; there is no inflow of water into the tank. What force must a truck engine produce to keep the truck stationary while the fire hose shoots a jet at 45 degrees at a volume flow rate of 2.4 m3/s ..
Benchmark the codes of conduct used by similar companies : 1. Briefly describe your company and then benchmark the codes of conduct used by similar companies in the industry. Critique the codes of conduct of at least three (3) similar companies in order to write codes for your company.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Make a schematic drawing of amorphous si glass with 10 h

if silcion is cooled quickly it will form glass instead of crystallyzingone way to do this is to deposit si atoms onto

  Determine a the time required for the train to travel the

a commuter train traveling at 40 mi h is 3 mi from a station. the train then decelerates so that its speed is 20 mi h

  A 1875 inch diameter shaft machined from aisi 1018 cd

a 1.875 inch diameter shaft machined from aisi 1018 cd steel supports a bending load during operation at 1750 rpm. if

  Concentric cylinder viscometer may be formed by rotating

A concentric cylinder viscometer may be formed by rotating the inner member of a pair of closely fitting cylinders (see Figure 1). For small clearances, a linear velocity profile may be assumed in the liquid filling the annular clearance gap. A visco..

  The bottom hole pressure in a well has been declining at a

the bottom hole pressure in a well has been declining at a constant rate of 1.4 psiday. the reservoir characteristics

  The mass flow rate is 15 kgs neglecting heat transfer and

steam enters a nozzle operating at steady state at 3 mpa 300oc with a velocity of 80 ms. the exit pressure and

  The length of a cast iron pipe is to be 4200 ft the head

the length of a cast iron pipe is to be 4200 ft. the head causing flow is to be 12.6 ft. after the pipe has been in

  All of the members of the 4-member frame shown have

all of the members of the 4-member frame shown have rectangular cross-sections 2 in. wide by frac12 in. thick. all pins

  A particle moves along the curve yx2 - 4m with a constant

a particle moves along the curve yx2 - 4m with a constant speed of 5 ms. determine the point on the curve where the

  Bob is asked to design a system for heating process water

bob is asked to design a system for heating process water in a chemical plant. the system is to heat 500 gallons of

  A 180-lb man and a 120-lb woman stand side by side at the

a 180-lb man and a 120-lb woman stand side by side at the same end of a 300-lb boat ready to dive each with a 16-fts

  A high school project involves building a model ultralight

a high school project involves building a model ultralight airplane. some of the stu- dents propose making an airfoil

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd