What is the transfer function of the system

Assignment Help Mechanical Engineering
Reference no: EM131079751

The response of a given system to a unit step u(t) = 1H(t) is given by

1408_81538a2d-9669-4c04-85f8-645716833879.png

What is the transfer function of the system?

Reference no: EM131079751

Questions Cloud

Werner herzog the director of the film : 1. Werner Herzog, the director of the film, whose voice you hear as the narrator, says at one point that "we are locked in history, and they [the Paleolithic painters who did the work in the Chauvet Cave] were not." Explain what you think he means..
Design and implement own version : For this question, you are required to design and implement your own version of the Position ADT and the Node List ADT. You are not allowed to use any of the built-in classes or interfaces provided by Java, which provide similar operations.
Deduce the currents i1(t) and i2(t) flowing in the loops : In the parallel network of Figure 5.9 there is no current flowing in either loop prior to closing the switch at time t = 0. Deduce the currents i1(t) and i2(t) flowing in the loops at time t.
Practices for security in rdbms : "Can you do some research and tell us a little on best practices for security in RDBMS' in regard to transactions?  What if a hacker takes money in a transaction sent to their account and then issue a ROLLBACK to the calling bank?"
What is the transfer function of the system : What is the transfer function of the system?
What expenditure for advertising will yield a maximum profit : The profit P (in hundreds of dollars) that a company makes depends on the amount x (in hundreds of dollars) the company spends on advertising according to the model. What expenditure for advertising will yield a maximum profit?
Assignment regarding the user frustration : The quality of the user experience is very important to the success of an application. In the early days of computing, users often experienced long delays since computing power was poor and networks had comparatively slow throughput. Modern system..
The chinese treasure fleet and the global empires : -Explain at least two (2) possible reasons for the differences between the results of exploration and trade by the Chinese and by the European states.
What can be said about the stability of each of the systems : What can be said about the stability of each of the systems?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The wood beam is subjected to a load of 12 kn if a grain

the wood beam is subjected to a load of 12 kn. if a grain of wood in the beam at pointa makes an angle of 25 degrees

  Find expressions for the average velocity at station 3 the

a fluid flows in a pipe with a sudden increase in its cross section as shown in the sketch. assume that the pressure in

  A 1kg mass connected to a horizontal spring of stiffness

a 1kg mass connected to a horizontal spring of stiffness 1031 nm has a dry-sliding friction force of 2 n. the mass is

  What is the work done on or by the steam

A piston-cylinder contains 0.1 kg of superheated steam at 180 ¯ C and 5.0 bars. The piston is frictionless and freely floating. Heat is added until the final volume is twice the initial volume.

  Determine the smallest possible value of the coefficient

determine the smallest possible value of the coefficient of static friction. (Assume that the sash is slightly smaller than the frame and will bind only at points A and B

  Calculate and plot the critical heat flux

A tube of 2-mm diameter is used to heat saturated water at 1 atm, which is in cross flow over the tube. Calculate and plot the critical heat flux as a function of water velocity over the range 0 to 2 m/s. On your plot, identify the pool boiling re..

  In each cycle of its operation a refrigerator removes 17j

in each cycle of its operation a refrigerator removes 17j of heat from the inside of the refrigerator and releases 40j

  Assuming that the coefficient of friction in cutting

Assuming that the coefficient of friction in cutting is 0.25 for turning a hard aluminium alloy on a 20 hp lathe (mechanical efficiency = 90%) with a width of cut of 0.24 in, a rake angle of 11°, and a cutting speed of 333 ft/min. Assume the cut is a..

  Determine the change in the rate at which the following

pressurized water pin 10 bar tin 110 deg c enters the bottom of an l 10-m-long vertical tube of diameter d 100 mm

  The data listed below are claimed for a power cycle

the data listed below are claimed for a power cycle operating between hot and cold reservoirs at 1000 k and 300 k

  If the arms and hub contribute 5 of the flywheel effect

a two cylinder engine with cranks at right angles developes 75 kw at mean speed 400 revmin.the coefficient of speed

  Derive the terminal velocity v0 when acceleration becomes

a sphere of solid density rho s and diameter d is dropped to a water pond density rho s and viscosity mu. initial

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd