Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A model grain dryer is being used to investigate the drying process. It is discovered that the load cell which supports the dryer indicates that the mass of the dryer and its contentsinitially increases during the heat-up. This phenomenon is to be investigated, and it is proposed that it may be caused by either of the factors:
a. Moisture in the hot drying air condensing on the cooler grain near the plenum of the bin (Hint: The vapor in the ambient will condense out if the temperature of a surface is lower than the incoming air dew-point temperature).
b. There is a false reading in the load cell (because there is no initial condensation taking place in this particular case) Could either (a) or (b) be true? The operating parameters of the bin are:Air mass flow rate (dry) = 0.15 kg/sec,Ambient dry bulb temperature = 23 ºC, Initial grain temperature = 20 ºC & Plenum temperature = 40ºC.
d.A computer simulation of the above dryer shows that towards the end of the drying time, air exits the drier at a relative humidity of 90%. What is the theoretical rate of moisture removal from the grain at this point, in kg/hr (Hint: It can be assumed that there is no heat loss through the walls, so the enthalpy of the plenum air will be the same as the enthalpy of the discharge air)
A piston-cylinder contains 40 kg water of which 20 kg is saturated liquid. The equilibrium pressure of the system is 100 kPa. a) Find the system initial volume b) The water undergoes an isothermal expansion until the pressure reaches 10 kPa.
Write an essay on the topic "application of geophysical techniques using electromagnetic induction as a tool for sustainable soil and water management of agricultural fields in the humid tropic Caribbean. components:
A 40 oF breeze of 10 miles per hour blows over the top of a round open-top water cooling tank which has a bulk temperature of 100 oF. What is the rate of energy in kW that enters into the air
What is the SI value of absolute pressure corresponding to a vacuum pressure of -10 inches of water. Assume the location is Moscow, Idaho. What is the SI value of gage pressure corresponding to a pressure 14 psia. Assume the location is Denver, Colo..
A cylinder with a 6.0 in., diameter 12.0 in. height is put under a compresive load of 150 kips. The modulus of elasticity for this specimen is 8000 ksi and Poisson's ratio is 0.35. calculate the final length and the final diameter of this specuman..
How to draw bending moment diagram for this shape and the value of the moment in critical sections assume that the distributed load (w) KN/M and the concentrated load
The man has a mass of 75 kg, and the beam has a mass of 40 kg. The beam is in equilibrium with the man standing at the end and pulling on the cable. Determine the force exerted on the cable by the man and the reactions at pinned support C.
what policies were implemented during and after WW1,WW2,Cold war?
Vehicles arrive at a toll booth with a mean arrival rate of 2 veh/min (the time between arrivals is exponentially distributed). The toll booth operator processes vehicles (collects tolls) at a uniform deterministic rate of one every 20 seconds. Wh..
a stream f gas flowing at 3000 cfm has a particulate loading of 50gr/ft what is the allowable exit loading if 95 % collection efficiency is required. what is the mass of the particles collected
Determine the liquid detention time, loading rate, F/M ration (with an MLSS of 2350 mg/l), sludge age (with 5330 lb/day waste sludge Eff. SS= 20 mg/l. Will the sludge settle properly
Start from the values for the density and the kinematic viscosity of CO2 at 15o C and standard atmospheric pressure (101.3 kPa), and first determine the value of the dynamic viscosity at the same conditions.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd