What is the temperature in kelvin assuming an adiabatic

Assignment Help Mechanical Engineering
Reference no: EM13627078

An oil well is drilled in the atlantic ocean, where the water depth is 350 meters.

a) Suppose methane gas forms a bubble in the drilling pipe, near the ocean floor with 1 (m^3) volume and temperature 2 C. What is the pressure in Pascals at this point?

b) Since the initial temperature is much higher than the critical point, it can be treated as an ideal gas, with (PV)^gamma= k, (k is a constant). gamma= (Cp/Cv) ~ 1.3 and STP gas density p=0.7 (Kg/m^3) for methane. Neglecting the possibility of chemical interactions and kinetic energy effects, if the bubble rises quickly to the surface (P= 1.01*10^5 Pa), calculate the volume in cubic meters of the gas bubble

c) What is the temperature in Kelvin assuming an adiabatic expansion of an ideal gas. Comment as to the extent to which the adiabatic expansion modle is valid for this situation (how accurate would you guess the calculation is?)

 

Reference no: EM13627078

Questions Cloud

Ten kilograms of ice at 260 k is dumped into 20 kg of : ten kilograms of ice at 260 k is dumped into 20 kg of liquid water initially at 300 k in an insulated container. the
Consider writing onto a computer disk and then sending it : consider writing onto a computer disk and then sending it through a certifier that counts the number of missing pulses.
A pneumatic lift system is being demonstrated at a sales : a pneumatic lift system is being demonstrated at a sales show. the total load is 70 kg and the lift piston is 15.2 cm
An ideal gas with molecular weight of 65 kgkgmol is : an ideal gas with molecular weight of 6.5 kgkgmol is compressed in a reversible manner from 690 kpa and 277 k to a
What is the temperature in kelvin assuming an adiabatic : an oil well is drilled in the atlantic ocean where the water depth is 350 meters.a suppose methane gas forms a bubble
A simple harmonic oscillator has a mass m0 on a spring of : a simple harmonic oscillator has a mass m0 on a spring of force constant k. the system is damped. it takes 10 cycles
The wires carry current in opposite directions if the : two wires parallel to each other and seperated by a distance d carry different currents they exert a force with
A cylindrical rod with a diameter of 25mm is subjected to a : a cylindrical rod with a diameter of 25mm is subjected to a torque of 500n?m and axial tensile force of 40kn.i draw a
A helicopter moves horizontally in the x direction at a : a helicopter moves horizontally in the x direction at a speed of 120 mih. knowing that the main blades rotate clockwise

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A 3000-lb car accelerates under constant power from 60

a 3000-lb car accelerates under constant power from 60 mileh to 90 mileh on a 0.25 mile straight level test track.

  Design a garage door controller using plc ladder diagram

Design a garage door controller using PLC Ladder Diagram (RSLOGIX 500 PLC SIMULATOR)

  The mechanical effficiency of the system is 80 what is the

it takes 15 seconds to raise a 1200 kg car and the supporting 300 kg hydraulic lift platform to a height of 2.8 m. the

  Consider a steam rankine cycle with superheat the maximum

consider a steam rankine cycle with superheat. the maximum temperature and pressure are 540 c and 60 bar and the

  Determine the air velocity

A Pitot-static probe connected to a water manometer is used to measure the velocity of air. If the deflection (the vertical distance between the fluid levels in the two arms) is 7.3 cm, determine the air velocity. Take the density of air to be 1.2..

  Drinking water at 10oc for an office complex must be pumped

drinking water at 10oc for an office complex must be pumped along a horizontal section of pvc pipe 50 m long at 2 ms.

  3 kg of r22 in a piston-cylinder is initially at a pressure

3 kg of r22 in a piston-cylinder is initially at a pressure of 0.30 mpa and volume of 0.15m3. the system is then heated

  Determine the work and heat transfer per unit mass each in

in a piston cylinder assembly refrigerant 134a undergoes a constant pressure process from saturated vapor at 8 bar to

  A white cast iron has 25 proeutectoid fe3c in its

a white cast iron has 25 proeutectoid fe3c in its microstructure.a calculate and find the composition of the cast

  Will the engineers decide to use the steel

Assume they test null hypothesis H0: versus H1: Will the engineers decide to use the steel if H0 is rejected? Will the engineers decide to use the steel if H0 is not rejected?

  Compute reactions of a simply supported continuous beam

Calculate reactions of a simply supported continuous beam. A beam is simply supported at the ends and is continuous over two spans.

  Calculate the engineering strain and the true strain for

a solid cylindrical specimen 200-mm high is compressed to a final height of 60 mm in two steps between frictionless

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd