Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.A horizontal pre-stressing force of 500kN is applied to rectangler beam. the beam has a depth of 500mm and a width of 250mm. the force is applied at a distance of 80mm below the x-x axis. what is the stress along the top edge and the bottom edge caused by the force?
2.Specifications require 96% compaction on a project. Maximum dry unit weight was found to be 114lb/ft^3 at a water content of 13.5% in labratory tests. Results of a field unit weight test were dry unit weight=111lb/ft^3 and a water content 11%. A sample in the field contained about 15% gravel sizes. Is the compaction satisfactory?
Determine the elastic and plastic section modulus of the I-beam. The axis runs through the center of the beam on both x and y axis (completely symmetrical). Beam properties: h= 12inches tf= 0.5 inches bf= 6 inches tw= 0.25 inches
Calculate the critical volume then estimate the green time interval for each phase of the intersection using the data provided below. Assume that the intersection will operate as a simple two phase cycle with a 90 second cycle length.
a horizontal curve on a single-lane highway has its PC at station 124 + 10 and its PI at station 131 + 40. The curve has a superelvation of 0.06 ft/ft and is designed for 70 mi/h. What is the station of the PT?
You have been hired to do a survey to search for old tunnels that are rumored to be in the area, previously used to smuggle people across the US-Mexico border. The tunnels are not expected to be exceptionally deep underground.
A 57.0 kg skier is being pulled up a 13.0° slope by a steelcable. The cable has a cross-sectional area of 7.18 10-5 m2. The cable applies a force tothe skier
The central angle is 35 degrees, the superelevation is 0.08, and 20.6 ft is cleared (for sight distance) from the inside edge of the innermost lane. Determine a maximum safe speed (assuming current design standards) to the nearest 5 mi/h.
You are a farmer. You plan to supply to your fields using water from a lake that is 500 ft above your fields using a 3 inch smooth plastic pipe, 1500 ft long. How much flow rate will you get? Initial guess: f=0.03, no pump.
What power must the pump supply to the system to pump the oil from the lower reservoir to the upper reservoir at a rate of .2 m^3/s. Sketch the HGL and the EGL for the system.
A horizontal circular plate weighing 60-lb is suspended from three wires that are attached to a support at D and form 30 degree angles with the vertical. Determine the tension in each wire.
It has been determined experimentally that the reaction follows frst order kinetics with respect to both oxygen andhydrogen sulfide concentrations: d[H2S]/dt =-k[H2S][O2]
A hydraulic jump occurs in an rectangular channel 2.3 m wide when the discharge is 2.5 m^3/s. If the upstream depth is 0.25 m calculate the depth downstream of the jump and the energy loss in the jump.
Water is to be boiledat sea level in a 30 cm diameter stainless steel pan on top of a3-kW electric burner. If60% of the heat generated by the burner is transferred to thewater during boiling, determinethe rate of evaporation of water.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd