What is the strain when the load is applied

Assignment Help Mechanical Engineering
Reference no: EM13216852

A cylindrical specimen of an aluminum alloy, has a Young's' Modulus of 59GPa, original length of 250mm, length at fracture of 254mm and a 0.2% yield stress of 287MPa. The specimen has a cross-sectional diameter of 15.2mm. If a load of 56KN is applied to it,

a) Will the specimen experience elastic or plastic deformation?

b) What is the strain when the load is applied?

c) What will be the length of the specimen after the load is removed? d) The specimen was reloaded until fracture. If the % reduction in area after fracture was 40%, what is the minimum diameter of the specimen at fracture?

 

Reference no: EM13216852

Questions Cloud

Determine the number of vehicles needed to satisfy : determine the number of vehicles needed to satisfy the indicated deliveries per hour? Assume that availability = 0.90.
Experiences and changes in anatomy of males and females : Use your own words to complete the table below with the experiences and changes in anatomy of males and females during the various sexual response phases
Determine the magnitude t of applied torque : the tank has a 180mm diameter and 12 mm wall thickness. knowing that the tank contains compressed air under a pressure of 8 Mpa, determine the magnitude t of applied torque for which the maximum normal stress in tank is 75 Mpa.
Explain total earnings of corporations : The economist Milton Friedman has proposed abolishing corporate income tax and taxing shareholders on the total earnings of corporations, rather than just on their own dividends.
What is the strain when the load is applied : What will be the length of the specimen after the load is removed? d) The specimen was reloaded until fracture. If the % reduction in area after fracture was 40%, what is the minimum diameter of the specimen at fracture?
Overall security objective deserves : What component of the overall security objective deserves the most attention in the environments mentioned in the article? What components would be less pertinent for these particular environments during a vulnerability assessment? Why?
What ways can thebusiness benefit from a web site : What Internet business model would be appropriate for the company to follow in creating a Web site and why and what ways can thebusiness benefit from a Web site?
What size of pipe would be required to move : what size of pipe would be required to move 30 milliliters of air in one minute at a pressure of 100 psi.
Maintain in accordance with the osha regulations : What case found that access to records that employers must maintain in accordance with the OSHA regulations, such as access to employee injury logs, may not require a warrant? "

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain working with boiler suspension bolts

Working with boiler suspension bolts. An HRT boiler is 4766mm long and 3533mm in diameter. It has 66 steel tubes with a diameter of 9mm. The total dry weight of the boiler is 2.565 tonnes

  Explain what will the ratio of the angle of twist

What will the ratio of the angle of twist be to that of the hollow shaft if the maximum shear stress in the material of 75 N / mm ^2 and what is the ratio of actual permissible shear stress?

  Determine the maximum angular velocity

The uniform rectangular plate is released from rest in the position shown. Determine the maximum angular velocity during the ensuing motion. Friction at the pivot is negligible.

  Explain complex loading bending and compression

Complex loading (bending and compression), A steel chimney is 28m high, 1.4m external diameter, and 20mm thick. It is rigidly fixed at the base and is acted upon by a horizontal wind pressure of intensity 1.

  What is the mass flow rate of oxygen

What is the mass flow rate of oxygen in lbm/s? Note that the inside diameter of a nominal 2 inch schedule 40 steel pipe is 2.067inches. Assume ideal gas principles apply.

  Determine the maximum contact pressure

The wheel of a crane lift is rolling on a flat rail. The radius of the wheel is 4 in, the contact length and force are 2.5 in and 1 ton respectively, and E = 30 MPa and ν = 0.3 for both parts. Determine (a) the maximum contact pressure, (b) the wi..

  A pitching wedge a golfer is using gives the ball a initial

A pitching wedge a golfer is using gives the ball a initial angle of 50 degrees, what range of velocities (Vo) will cause the ball to land within 3 ft of the hole?

  What is the ideal mechanical advantage of the wedge

A hydraulic shear applies 2000 lb force to a wedge. It is used to shear plate steel to rough size. The shear has a 1/4 inch thick cutting blade with a 45 degree slope. What is the ideal mechanical advantage of the wedge?

  Design value for the molded friction material and steel disk

Design value for the molded friction material and steel disks to be used 0.06 and pressure max=1400kpa. Determine appropriate values for the disk inside dimmeter, the total number of disks and the actuating force?

  What is the air temperature at the stagnation point

A high performance F-16 fighter is flying at Mach 0.96 at sea level. What is the air temperature at the stagnation point at the leading edge of the wing?

  Derive an expression for the net work transfer

(a) derive an expression for the net work transfer for the cycle. Prove that for a Stirling Cycle, the net work transfer is always from the system to the surroundings.

  Determine the initial and final pressures

Friction between the piston and the cylinder wall can be neglected. For the air, determine the initial and final pressures, in kPa, and the work, in kJ.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd