What is the steam quality exiting the low pressure turbine

Assignment Help Mechanical Engineering
Reference no: EM13713284

Reheat is added to an ideal Rankine steam power cycle to improve it’s efficiency and turbine exit quality. Steam enters the HP turbine at 15 MPa and 600C. Steam exits the HP turbine at 4 MPa and enters the boiler for reheat. Then the steam enters the LP turbine at 600C. Condenser pressure is 10 kPa. Assume pump efficiency is 90% and turbine efficiency is 88% (for both turbines).

a. What is the Steam quality exiting the low pressure turbine

b. Overall thermal efficiency for the cycle

Reference no: EM13713284

Questions Cloud

Determine the fin efficiency : Consider a two- dimensional, straight triangular fin of Length L= 50mm and base thickness t= 20mm. The thermal conductivity of the fin is k= 25 W/mK. The base temperature is T_b= 50 degrees Celsius, and the fin is exposed to convection conditions cha..
Assumptions about the drop size and the unit cost of energy : A 1982 U.S. Department of Energy article (FS#204) states that a leak of one drip of hot water per second can cost $1.00 per month. Making reasonable assumptions about the drop size and the unit cost of energy, determine if this claim is reasonable. S..
Gas in a piston-cylinder undergoes a carnot power cycle : A gas in a piston-cylinder undergoes a Carnot power cycle. The gas expands and compresses isothermally between two reservoirs at 600 K and 300 K.
Developing an appreciation for hr competencies 2020 : Understanding the Trends that are re-shaping the world and understanding the Future Workplace and Future Workforce -2020
What is the steam quality exiting the low pressure turbine : Reheat is added to an ideal Rankine steam power cycle to improve it’s efficiency and turbine exit quality. Steam enters the HP turbine at 15 MPa and 600C. Steam exits the HP turbine at 4 MPa and enters the boiler for reheat. Then the steam enters the..
The fraction of steam extracted for feed water heating : Consider an ideal Rankine cycle with a single open feed water heater. The boiler pressure is 800 psia, and the condenser pressure is 2 psia. Steam is extracted from the turbine to heat the feed water at 90 psia. Steam enters the turbine at 1000F.
Theoretical air and burned : Methane (CH4) is mixed with 125% theoretical air and burned.
Kind of problem an angular momentum-impulse equation : Explain in 4 to 5 sentences at least in what cases/in what kind of  problem  an angular momentum-impulse equation and concept can be reduced  to conservation of angular momentum. Give an example of a problem where conservation of angular momentum is ..
Decorative water fountains consist of a water reservoir : Decorative water fountains consist of a water reservoir and underground piping to and from a pump. One such system is shown schematically in the figure. The pipe material is PVC(a table is provided). The outlet line from the pump is 18 m and the inle..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd