Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The City of Leadville (dimensions 120x120km ) is characterized by an average daily emission rate of 5000kg/d of particulate lead into the atmosphere from auto exhaust and industrial processes. The background concentration of atmospheric lead is 0.1 ug/m^3. During a typical hot day in Leadville the mixing height is 500m and the average wind speed is 1.9m/s. A typical lead particle deposition flux,Jd , for similar meteorological conditions is 0.05cm/s .
a)What is the steady-state concentration of lead in the urban air?
(Hint: note that the mass flow rate of Pb Particles from the air and to the earth (mass of Pb deposited/time) is given by Qd x C, where ,Qd=Jd x A, C is the concentration of lead in the air above the city, and A is the surface area of the city)
A 3400-lb car is traveling in third gear (ratio 2.5 to 1) on a level road at its top speed of 130 mi/h. The air density is 0.00206 slugs/cuft. The car has frontal area of 19.8 sqft, a drag coefficient of 0.28, a wheel radius of 12.6 inches, a driv..
Consider a 2014-T6 aluminum alloy the S-N behavior. A cylindrical rod of diameter 13.2 mm fabricated from this alloy is subjected to repeated tension-compression loading along its axis.
What is the maximum load that a .75" diameter steel cable can hold if the UTS of the steel is 145,000 PSI and a safety factor of 1.5 is required.What is the stretch of the 360" cable under this load
calculate the: 1) molar concentration of metal ion in the stock coagulant solution; 2) coagulant feed rate (into the process water flow stream) in units of L/day and L/min; 3) alkalinity consumed (in the process water flow stream) in units of mg/L..
How are compacted and loose bulk density used in real life. Also is a high degree of accuracy necessary in the bulk density tests
Given the data , design a section of sanitary sewer to carry these flows at minimum velocity of 2.5 fps. Assume that the minimum depth of the sewer below the street must be 8.5 ft and that an n value of 0.013 is applicable.
given bulk density as 1300kgcubic meter and field capacity as 22 by weight and permanent wilting point as 10 by
A gas stream with a particulate loading of 20.0g/m^3 is passed through a 70%-efficient cyclone followed by a 95%-efficient ESP. Calculate the overall efficiency of the system.
The preliminary design for a wastewater treatment plant is being developed. The wastewater flow rate is 10,000 m3/day, and the BOD5 concentration is 200 mg/L. The plant discharge standard is 30 mg/L as BOD5.
it has been calculated that the maximum density for the soil will be obtained when the water content reaches 21.5%. Compute how many grams of water must be added to each 1000g of soil( in its natural state) in order to increase the water content 2..
DISCUSS THE LIMITATION AND PROBLEM OF EXTRAPOLATING MECHANICAL PROPERTIES MEASURED ON A SMALL ROCK SAMPLE TO FIELD SITUATIONS.
Water in a hydraulic press is subjected to a pressure of 4500 psia at 68 degrees F. If the initial pressure is 15 psia, approximately what will be the percentage decrease in specific volume
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd