What is the spring constant required

What is the spring constant required

Assignment Help Electrical Engineering

Reference no: EM131087169

A low-force sensor uses a spring and a 1-k? linear pot. The pot has a 1-in. stroke and a supply voltage of 10 Vdc. If the sensor is to have an output of 1 V per 10 lb of load, what is the spring constant required?

Reference no: EM131087169

Questions Cloud

Calculate the force on the bar : Draw a schematic of the set up and calculate the force on the bar.

Draw a schematic of the set up and calculate the force : Draw a schematic of the set up and calculate the force

Create and sell low-risk assets : The process where financial intermediaries create and sell low-risk assets and use the proceeds to purchase riskier assets is knownas

Calculate the consumer demand : Calculate the consumer's demand, and his utility, when beer and pizza are each taxed at $0.20 per unit. How much revenue does the government raise with this tax

What is the spring constant required : what is the spring constant required?

What pressure does the sensor report : What pressure does the sensor report?

What pressure does the sensor report : What pressure does the sensor report?

What is the temperature at the hot junction : What is the temperature at the hot junction?

The binomial approximation give satisfactory results : Consider the single-sample plan with c = 2 and n = 50, as discussed in Example 16.11, but now suppose that the lot size is N = 500. Calculate P(A), the probability of accepting the lot, for p 5 .01, .02,..., .10, using the hypergeometric distribut..

Reviews

Write a Review

Required(*) Message

Electrical Engineering Questions & Answers

Amplify the signal of a microphone with internal resiatance

What value of emitter resistor would you choose, if: a) You have to amplify the signal of a microphone that has an internal resistance of 100K using a Common Emitter bias configuration b) you have to drive a load of 50 with an Emitter Follower cir..

Determine what is the net electric field at location

A small object with charge Q1=6nC is located at the origin. A second small object with charge Q2=-5nC is located at m. What is the net electric field at location A m due to Q1 and Q2

What is the shaft speed in radians per second

A motor's shaft is spinning at a speed of 1800 r/min. What is the shaft speed in radians per second

Derive a minimum boolean expression for the output z

A combinational logic circuit has two control inputs, C1 and C2, two data inputs, A and B, and one output, Z. Design a logic circuit that performs the logic operations on the two data inputs as specified in the table below: C1 C2 Logic Function

Project on lfc using tuned fopid i have considered a two

project on lfc using tuned fopid. i have considered a two area model. need help regarding implementation of ga matlab

Find what is the themal efficiency of the engine

If the work output is 10kW, find the required heat transfer rate from the high to the low temperature source, and the required heat transfer rate to the low temperature source. What is the themal efficiency of the engine

What is the frequency of the current in radians per second

A 40 kHz sinusoidal voltage has zero phase angle and a maximum amplitude of 2.5 mV. When this voltage is applied across theterminals of a capacitor the resulting steady-statecurrent has a maximum amplitude of 125.67μA

What is the output of the correlator for user1 for first bit

Sketch the baseband signals for the two users when user 1 sends the bits 011, and user 2 sends the bits 101. Add the signals for the first bit only, and show that the output of the correlator for user 1 is -4, corresponding to a 0

How far down the hill does the shell strike

How far down the hill does the shell strike

An active network is described by the characteristic equatio

It is required that the network be stable and that no component of its response decay more rapidly than K1e^-3t. Show that these conditions are satisfied if K2>0, |K1| 3K1. Crosshatch the area of permitted values of K1 and K2 in the K1-K2 plane.

Calculate a-phase line current and a-phase line voltage

Y- Delta connected; Source voltage in the b-phase is 20 angle (-90) V (rms); Source phase sequence is acb; Line impedance is (1+j3) Ohms/phase; Load impedance is (117- j99) Ohms/phase.Draw the single-phase equivalent for the a-phase.

Find the largest possible number of independant vectors

Find the largest possible number of independant vectors v1=column[1 -1 0 0] v2= column[1 0 -1 0] v3=column[ 1 0 0 -1] v4= column[ 0 1 -1 0] v5= column[0 1 0 -1] v6= coolumn[ 0 0 1 -1] note all are column vectors

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd