User Account

All Pages

What is the speed of the truck

Assignment Help Electrical Engineering
Reference no: EM131076903

An object falls from a building that is 35 m above the ground.Itfalls directly into a truck, moving with constant velocity thatis6 m from the point of impact when the object is released.

a). How long does it take for the object to reach the ground?

b). What is the speed of the truck?

Reference no: EM131076903

Questions Cloud

What is limitation of relying on spellcheck and grammarcheck : What is one limitation of relying on SpellCheck and GrammarCheck during the editing process?
What is the amplitude of motion for mass : The maximum speed of a 3.1 -kg mass attached to a spring is 0.70 m/s, and the maximum force exerted on the mass is 13 N. (a) What is the amplitude of motion for this mass?
Use the ansi recommendations for keyway design : 1) he rotating 1050 cold rolled steel shaft shown in the figure below is simply supported at the center of two bearings (denoted by an X) and the only applied load is the constant 7kN load. All dimensions are in mm and all steps in the shaft have ..
Write a c++ interface for a double-ended list : Write a C++ interface for a double-ended list.
What is the speed of the truck : a). How long does it take for the object to reach the ground? b). What is the speed of the truck?
What is its acceleration : (a) How long does the electron take to travel this 1.50 cm? (b) What is its acceleration?
How do social control and social bonding explain conformity : While the pressure to conform is intense, people continue to deviate. Using either Merton's Strain Theory or Becker's Labeling Theory, explain why some people choose to become deviant.
Determining the horizontal and vertical components : a. How long does it take the plate to fall to the floor? b. How far from the base of the counter does the plate hit the floor? c. What are the horizontal and vertical components of the plate's velocity just before it hits the floor?
Repeat the previous programming problem : When the size of the array is greater than 20 and the number of entries in the list is less than half the size of the array, reduce the size of the array so that it is three quarters of its current size.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is output frequency and duty cycle of the final stage

If the MOD-8 binary counter is driven by a 10 MHz input clock with a 5% duty cycle, what is the output frequency and duty cycle of the final stage

  Determine mechanical power supplied to the load

When the motor runs at 1710 rpm, the line currentdrawn from the supply is 78 A at 0.85 PF lagging. Given that,stator iron loss is 2kW, windage and friction losses are 1.2kW andresistance between two stator terminals = 0.4W

  Draw schematic diagram for half wave and full wave rectifier

Draw the schematic diagrams for half wave and full wave rectifier and their typical output waveform. Also write formulae to determine i) Peak load voltage ii) DC load current

  Calculate the per unit impedance of the transformer

Calculate the per unit impedance of the transformer using base values of 1 MVA and 400 V. (and .)

  Suppose that 3 j of work is needed to stretch a spring from

suppose that 3 j of work is needed to stretch a spring from its natural length of 26 cm to a length of 42 cm. a how

  What is the minimum output voltage of the discriminator

An FM receiver has a Foster Seeley discriminator that has a transfer ratio K = 0.03v/khz. If the maximum IF deviation is 75Khz, what is the maximum output voltage of the discriminator What is the minimum output voltage of the discriminator

  Determine the values for the period and duty cycle registers

A PWM is used in 8-bit mode to produce a signal with a 1 msec period and 60% duty cycle. Determine the value required for any pre-scaling, and the values for the period, and duty cycle registers. The E-clock is 24 MHz.

  Find the voltage reflection coefficient of transmission line

A lossless transmission line, with characteristic impedance of 50Ω and eletrical length of l=0.27λ, is terminated by load impedance 40-j25Ω. Determine voltage reflection coefficient.

  Explain the different operating modes of 8255

Explain the different operating modes of 8255 in microprocessor 8255? Explain in detail traffic light based microprocessor?

  Calculate v1 in the solution worked out on the site

since v1 is not the voltage across the 7ohm resistor but the voltage across the 9 ohm equivalent resistor shouldn't the current be found by dividing v1 by 9 omhs

  Digital processing of an analog signal

What is the configuration of system for digital processing of an analog signal? a) Analog signal|| Pre-filter ->D/A Converter -> Digital Processor -> A/D Converter -> Post-filter

  Calculate the output resistance of the device

Calculate the output resistance of the device, dIC/dVC, for 0

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd