What is the sample period ts

Assignment Help Electrical Engineering
Reference no: EM13219377

A continuous-time signal x(t) = sin(20πt) + cos(40πτ) is sampled at rate fs=1/Ts to form the discrete-time signal x[k] = sin(πk/5) + cos(2πk/5).

What is the sample period Ts?

 

Reference no: EM13219377

Questions Cloud

What is the approximate discrete-time equation : What is the approximate discrete-time equation the models the continuous-time impulse response for fs=1kSa/s and RC=10^-2?How to solve this problem?
Determine the relative permittivity of the dielectric : Determine the relative permittivity of the dielectric, the maximum and minimum electric field intensities in medium 1 and the electric field intensity in medium 2.
How much coal did we burn : The residential sector of PA consumed about 150.6x1012 Btu of electricity (www.eia.doe.gov). Assuming all of this energy comes from bituminous coal with a heating value of 14,000 Btu/lb. How MUCH coal did we burn?
What is the system nyquist sample rate : What is the system's Nyquist sample rate if ω0 = 1000/(2π) rad/sec.?
What is the sample period ts : What is the sample period Ts?
How much charge passes through a cross section : the ends of a length of wire are labeleda and b. If the current in the wire is iab = -3A, are electrons moving toward a or b? How much charge passes through a cross section of the wire in 3 seconds?
Explain why pricing policy may not be good news for consumer : Suppose the two rival office supply companies Office Depot and Staples both adopt price matching policies. If consumers can find lower advertised prices on any items they sell, then Office Depot and Staples guarantee.
What is the value of q we need to inject : If we want to correct the power factor to 0.9 lagging, what is the value of Q we need to inject.
Find current of phase b in polar form : In a balanced three-phase system the Y-connected impedances are 3∠60°Ω. If V_bc=480∠-75° V, find current of phase "b" in polar form.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Implementation of ga matlab code

Project on LFC using tuned FOPID. I have considered a two area model. Need help regarding implementation of GA MATLAB code for a two area interconnected power system for LOAD FREQUENCY CONTROL.

  Realize the storage circuits for n1 and n2

Realize the storage circuits for N1 and N2 as describe in the design specification.

  How much should be deposited

An indiviual wishes to deposit an amount of money now and $100 every six months so that at the end of five years $1500 will have been accumulated. With interest 4% per year, compounded semiannually, how much should be deposited?

  Compare a lumped element model of a lossless transmission

Compare a lumped element model of a lossless transmission line (single L and C) with the distributed model. Use the following values for the transmission line in this comparative analysis.

  Explain scada system

Explain the function of the HMI in a SCADA system.

  Determine the maximum and minimum spectral frequencies

Determine the maximum and minimum spectral frequencies received from a stationary GSM transmitter that has a center frequency of exactly 1950.000000 MHzassuming that the receiver is traveling at speeds of.

  Explain the critical radius of insulation.

Explain the following terms; (i) critical radius of insulation. (ii) economic lagging thickness.

  What is the value of q we need to inject

If we want to correct the power factor to 0.9 lagging, what is the value of Q we need to inject.

  Approximation of quarter circle using bezier curve

Approximation of quarter circle using Bezier curve, Determine the Bezier curve of order 3 that approximates a quarter circle centered at (0,0), (1,0), (0,1).

  Explain a square wave signal with voltage levels

A square wave signal with voltage levels 0 volts and 2.0 volt at a frequency of 1.00 MHz is multiplied by a sine wave at a frequency of 5.0 MHz

  Shielding effectiveness with copper also steel at equality

Shielding Effectiveness with copper and steel at equality, Determine the frequency at which two 1 mm thick shields, one made of copper and the other of steel

  How tall must the antennas be if the link operates

How tall must the antennas be if the link operates on a frequency of 2.450Ghz, D1=5miles, D2=11miles, and the obstruction is 60 feet high?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd