User Account

All Pages

What is the resolution of the output

Assignment Help Electrical Engineering
Reference no: EM131208858

Assume the full-scale value of the analog input voltage to a particular analog-to-digital converter is 10 V.

a. If this is a 3-bit device, what is the resolution of the output?

b. If this is an 8-bit device, what is its resolution?

c. Make a general comment about the relationship between the number of bits and the resolution of an ADC.

Reference no: EM131208858

Questions Cloud

How many bits are required in the dac : A DAC is to be used to deliver velocity commands to a motor. The maximum velocity is to be 2,500 rev/min, and the minimum nonzero velocity is to be 1 rev/min. How many bits are required in the DAC? What will the resolution be?
Balance sheet-assets-liabilities and stockholders equity : The balance sheet includes assets, liabilities, and stockholders’ equity as of a point in time. One example of an operating revenue would be the revenue created by the sale of an automobile at a car dealership. Superior has provided the following inf..
Write a program to test the balance condition : Given a bridge composed of series impedances in each branch, write a program to test the balance condition as defined by given equation.
Demonstrate the methods on your problems : State what methods you will use and then demonstrate the methods on your problems, explaining the process as you go. Discuss any particular challenges those particular polynomials posed for the factoring.
What is the resolution of the output : Assume the full-scale value of the analog input voltage to a particular analog-to-digital converter is 10 V.
How many bits are required for the dac : The voltage range of feedback signal from a process is -5 V to +15 V, and a resolution of 0.05 percent of the voltage range is required. How many bits are required for the DAC?
Determine the current through the resistor r1 : Write the mesh equations for the networks of given figure.  - Determine the current through the resistor R1.
What is the maximum frequency content : What is the maximum frequency content that the analog signal can have according to the Nyquist criterion?
Define what consider to be your strengths as communicator : Define what you consider to be your strengths as a communicator. Consider talking, listening, empathy, and so on. Discuss what you consider to be some important areas for improvement in your communication.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Write the boolean expression for each output bit

Write the (optimal) Boolean expression for each output bit.

  Design a 10-to-4 encoder with inputs in the1-out-of-10 code

Design a 10-to-4 encoder with inputs in the1-out-of-10 code and outputs in a code like normal BCD except thatinput lines 8 and 9 are encoded into "E" and"F", respectively.

  Find the matching circuit consist of ideal capacitor

For a complex load of 100 + 25 j ohm. find the matching circuit consist of ideal capacitor and/or inductor to match the load to 50 ohm impedance at 500MHz. The solution should include circuit schematic and values of each component

  Determine the lateral shift at the output of the plate

Determine the lateral shift at the output of the plate and the retardation between the ordinary and extraordinary beams - Sketch the beams

  What is voltage produced at the terminals of the inductor

1) A 5H inductor changes its current by 6 A in 0.4s. The voltage produced at the terminals of the inductor is 2) An RL circuit has R=2 ohms and L=4. The time needed for theinductor current to reach 40% of its steady state value is

  Physical and chemical equations used in process models

Give the schematic table that has the Physical and chemical equations used in process models used in measurement systems.

  Determine efficiency of transformer for secondary current

A single-phase, 100-kVA, 1000:100-V, 60-Hz transformer has the following test results: Open-circuit test (FIV side open): 100 V, 6 A, 400 W Short-circuit test (LV side shorted): 50 V, 100 A, 1800 W 1)Determine the voltage regulation at 75% of the rat..

  What is the computational power of electronic devices

Estimate the size and weight of an 1970 automobile using 1970 electronics technology which would have the equivalent computational power and electronics a typical 2013 automobile.

  Write the expressions for the voltages vc and vr

The capacitor of given figureis initially charged to 40 V before the switch is closed. Write the expressions for the voltages vC and vR and the current iC for the decay phase.

  What is the rate at which the entropy of the low-temperature

What is the rate at which the entropy of the low-temperature reservoir is changing. What is the rate at which the work production is changing the entropy of the engine surroundings

  Calculate the continuous distribution function

The probability density function (PDF) of a continuous random variable is given in Fig.- Calculate the Continuous Distribution Function (CDF) and do its plot.

  Define the necessary number of states

Design an FSM that recognizes an input sequence that has at least three 1's. More specifically, the FSM has one input, X, and one output, Y. Define the necessary number of states and what each state represents

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd