What is the reaction force on each of the joists

Assignment Help Mechanical Engineering
Reference no: EM131306985

A 1 in × 10 in plank on a redwood deck has L = 48 in long and supported on three joists that rest on the ground and so do not bend. The joists act as pin/roller supports for the plank. If a 130 lb person stands on the plank in the location shown, what is the reaction force on each of the joists?

337_2c18abfe-83fc-4313-8193-27a28fac18c5.png

Reference no: EM131306985

Questions Cloud

How much strain energy u is stored in the beam : A simply supported beam of length L is subjected to loads that produce a symmetric deflection curve with maximum deflection at the midpoint of the span.
Determine the tip deflection of this cantilever : Use Castigliano's second theorem to determine the tip deflection of this cantilever with a length L, a constant E I, and a linearly increasing load with a maximum force/length q0. Confirm your result using Table 9.1.
Determine how much the water utility must purchase : Use this information to produce a simulation to determine how much the water utility must purchase for the next 3 months.
What is the new volume of the gas : 20 cubic inches of a gas with an absolute pressure of 5 psi is compressed until its pressure reaches 10psi. What is the new volume of the gas? (Assume that there's no change in temperature.)
What is the reaction force on each of the joists : If a 130 lb person stands on the plank in the location shown, what is the reaction force on each of the joists?
Determine the rate of heat transfer from the combustion : Gaseous ethanol (CH3CH2OH, also expressed as C2H5OH) is burned with 200 % of theoretical air at standard conditions. During the combustion process 90% of the Carbon in the fuel is converted to CO2 and 10% is converted to CO. Determine the rate of ..
What is the strongest correlation in this matrix : The strongest correlation in the matrix is the physical and mental health sample population with a physical health score with an r = -134 and mental health component score of r -133. What is the strongest correlation in this matrix is doctors' visi..
Discuss ethical and professional and legal issues : Discuss ethical, professional and legal issues which you consider arise from scenario.- Make some recommendations of actions which could be taken to resolve situation or to minimize the chance the scenario may recur.
Determine the normal stress as a function of x : On the same axes, plot this normal stress, as well as the normal stress in a cantilever of the same length with a constant width bL /2. Both beams have the same volume of material-which can carry a higher load P?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd