What is the ratio of the area at this location to entrance

Assignment Help Civil Engineering
Reference no: EM131036191

Air enters a nozzle at 30 psia, 630 R, and a velocity of 450 ft/s. Assuming isentropic flow, determine the pressure and temperature of air at a location where the air velocity equals the speed of sound. What is the ratio of the area at this location to the entrance area?

Reference no: EM131036191

Questions Cloud

Compute the cumulative incidence of heart attack : A study is conducted in order to determine the relationship between estrogen therapy and heart attack. Compute the cumulative incidence of heart attack in women who do take estrogen? Round to three decimal places
What people ought and ought not to do in various situations : Rules of conduct describing what people ought and ought not to do in various situations are called. Which of the following is an argument in favor of the divine command theory?
How does the diverging section affect the pressure : Consider the isentropic flow of a fluid through a converging-diverging nozzle with a subsonic velocity at the throat.
Designing a low-cost pollution prevention plan : Review the Reading Assignment titled as "Designing a Low-Cost Pollution Prevention Plan to Pay Off at the University of Houston" by Bialowas, Sullivan, and Schneller.
What is the ratio of the area at this location to entrance : Assuming isentropic flow, determine the pressure and temperature of air at a location where the air velocity equals the speed of sound. What is the ratio of the area at this location to the entrance area?
Total annual costs of holding and ordering : a. What is the EOQ? b. Wat are the total annual costs of holding and ordering c. How many orders should D-M place with Specialty Lighting per year?
Determine the back pressure that will result in an exit mach : Air enters a converging-diverging nozzle at 0.5 MPa with a negligible velocity.
Injection molding department of a company : The injection molding department of a company uses an average of 30 gallons of special lubricant a day. The supply of the lubricant is replenished when the amount on hand is 170 gallons.
What do the states on the fan no line and the rayleigh line : What do the intersection points of these two curves represent?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the daily discharge per 1000 feet into the river

A canal was constructed running parallel to a river 1500 ft away. Both fully penetrate a sand aquifer with a hydraulic conductivity of 1.2 ft/d. The area is subject to rainfall of 1.8 ft/y and evaporation of 1.3 ft/y.

  Determine what angle of twist

a beryllium copper wire having diameter of 1-50 mm and length of 40mm is used as a small torsion bar in an instrument. determine what angle of twist would result in the wire when it is stressed to 250 mpa.

  What is the recommendation to get a basic refrigerator

Quinton's refrigerator has just died. He can get a basic refrigerator or a more efficient refrigerator with an energy star designation. Quinton earns 4% compounded annually on his investments, he wants to consider a 10-year planning horizon

  Calculate the heat transfer and calculate the work done

ten kilograms of saturated liquid water at 5 bar is heated in a piston-cylinder assembly at constant pressure until temperature reaches 400 degrees C. A. Show the process on a T versus v diagram.

  Plot the three values on the same diagram and comment on the

A wave has a height of 1.5 m in water 5 m deep and a wave period of 6 s. Plot the horizontal component of velocity, the vertical component of acceleration, and the dynamic pressure at a point 2 m below the still water level versus time for a 6-s inte..

  Find the rate that the trucks line up

A container ship carries 2000 units. It must be unloaded andre-loaded in a 48 hr turnaround. Two cranes are available. Find the rate that the trucks line up, load and pass under each crane.

  Determine the value for cu and the cohesion intercept c

At failure, the respective minor and major principal stress values are 20 kPa and 46 kPa for one and 40 kPa and 80 kPa for sample two. From these data, determine the value for (phi)cu and the cohesion intercept c on the Mohr's circle shear stress ..

  Determine the force in each member of the truss

Determine the force in member AB Determine the force in member AE Determine the force in member BC Determine the force in member BE Determine the force in member CD

  Determine the minimum possible area of the metal plate

A circular hole of diameter 11.42 + and - 0.03 inches is cut out of the plate. Also, using the tolerances given, determine the minimum possible area of the top surface of the metal plate.

  What return period must an engineer use in the design

What return period must an engineer use in the design of a bridge opening for a 50% risk that flooding will occur at least once in two consecutive years? Repeat for a risk of 100%.

  Find the bod concentrations at the outlet of both lagoons

The municipal wastewater treatment process for a hypothetiical town consists of two separate lagoons being operated in series. The first lagoon has a volume of 4 million gallons, while the second lagoon has a volume of 2.5 million gallons.

  At what minimum slope can be laid such that velocity is less

At the design flow, it is intended to have a relative depth of 0.8. At what minimum slope can it be laid such that the velocity is at least 2 ft/s at design flow and depositied solids will be scoured out by the deisgn flow

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd