What is the rate of heat loss from the steam line

Assignment Help Mechanical Engineering
Reference no: EM131281618

An overhead 25-m-long, uninsulated industrial steam pipe of 100-mm diameter is routed through a building whose walls and air are at 25°C. Pressurized steam maintains a pipe surface temperature of 150 C, and the coefficient associated with natural convection is h 10 W/m2 · K. The surface emissivity is ε = 0.8.

(a) What is the rate of heat loss from the steam line?

(b) If the steam is generated in a gas-fired boiler operating at an efficiency of ηf = 0.90 and natural gas is priced at Cg = $0.02 per MJ, what is the annual cost of heat loss from the line?

Reference no: EM131281618

Questions Cloud

Describe the potential sources of funding : OL 330:Describe the potential sources of funding you have found for your project. (Examples can include program support, seed money to start the project, or funding for operating expenses, research, emergency funds, or annual funds.) Justify why ea..
Difference between the price elasticity of demand : What is the difference between the price elasticity of demand along a straight line demand curve and the rate of change along the demand curve?
Difference between back and front surfaces : If 4 W are being dissipated in circuits mounted to the back surface of the chip, what is the steady-state temperature difference between back and front surfaces?
Trade and labor mobility : Suppose that the U.S. dollars-Canadian dollars exchange rate is flexible and is determined by the forces of demand for and supply of the two currencies. Assume also that labor is mobile between the United States and Canada due to low transportatio..
What is the rate of heat loss from the steam line : If the steam is generated in a gas-fired boiler operating at an efficiency of ηf = 0.90 and natural gas is priced at Cg = $0.02 per MJ, what is the annual cost of heat loss from the line?
Are all workers with occupational injuries protected by ada : Are individuals who are perceived as having handicaps, but in fact either have recovered from the disability or are not handicapped, covered by the Rehabilitation Act of the ADA ?- Are all workers with occupational injuries protected by the ADA?
What factors must be proved to establish the case : Mazir Coleman drove a school bus for the Casey County, Kentucky, Board of Education for four years.- What factors must be proved to establish his case? Decide.
What is its surface temperature : If the probe surface has an  emissivity of 0.8 and the probe does not receive radiation from other surfaces, as, for example, from the sun, what is its surface temperature?
What factors must the court consider : What factors must the court consider in evaluating Heron's claim? What result should the court reach in this case? Decide.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd