What is the proeutectoid phase

Assignment Help Mechanical Engineering
Reference no: EM13216839

Consider 6.0 kg of austenite containing 0.45 wt% C, cooled to below 727 degrees Celcius (1341 degrees Farenheit).

a) What is the proeutectoid phase?
b) How many kilograms each of total ferrite and cementite form?
c) How many kilograms each of pearlite and the proeutectoid phase form?
d) Schematically sketch and label the resulting microstructure.

 

Reference no: EM13216839

Questions Cloud

Sensitive business information : Under certain circumstances, employers can request OSHA protect proprietary and sensitive business information that they submit to the agency.
How policy concerns may differ at each hospital : Discuss how policy concerns may differ at each hospital, as well as differences in executive management team. Include at least two reference from The Federal Register, addressing hospital boards.
What is the concentration of fecl3 in a solution : What is the concentration of FeCl3 in a solution prepared by dissolving 20.0 g of FeCl3 in enough water to make 275 mL of solution?
Uniform crime report and self-report data : Complete the matrix below. To complete this matrix, list two pros and two cons of Uniform Crime Report (UCR) data and two pros and two cons of self-report data.
What is the proeutectoid phase : Consider 6.0 kg of austenite containing 0.45 wt% C, cooled to below 727 degrees Celcius (1341 degrees Farenheit).
How increasing the attractiveness of the debt securities : Both convertibility and warrants attached to debt aim at increasing the attractiveness of the debt securities and lowering the interest cost.
Determine the amount of heat that must be removed : A vessel with a volume of 0.0011 m3 is filled with dry saturated steam at a pressure of 95 kPa. It is then sealed and cooled to 250C. Determine the amount of heat that must be removed.
Calculate the adiabatic flame temperature : Calculate the adiabatic flame temperature (at constant pressure) for ethane C2H6 in air
State political practices-impact human resource management : When businesses operate across countries, how does diversity-in cultures, socioeconomic factors, or political practices-impact human resource management?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain finding exit velocity from air nozzle

Finding exit velocity from air nozzle, Air enters a nozzle operating at steady state at 800 ºR with a negligible velocity and exits the nozzle at 570 ºR.

  Which one has the bigger moment of inertia

two spinning discs have the same angular momentum, but disk 1 has more kinetic energy than disk 2. Which one has the bigger moment of inertia - explain your reasoning?

  What is the velocity of the collar

The system is at rest in the position shown, with the 12-lb collar A resting on the spring (k = 20 lb/ft), when a constant 30-lb force is applied to the cable. What is the velocity of the collar when it has risen 1 ft? The collar is attached to th..

  An airfoil of surface area 1ft squared is tested for lift

Lift coefficient (Cl) and lift (L), An airfoil of surface area 1ft squared is tested for lift (L) in a wind tunnel. At an angle of attack of 5 degrees with standard air of density 0.0024 slugs/ft cube at a speed of 100 ft/sec

  Find velocity distribution in the film

find a) velocity distribution in the film b) shear stress distribution c) volumetric rate of flow d) average velocity. assume the flow is steady and laminar.

  Calculate the time for the ice to completely melt

If the chest is completely filled with ice, calculate the time for the ice to completely melt. State your assumptions. The enthalpy of fusion for water is 330 kJ/kg.

  Estimate the tension on the mooring line caused

the dredger is loading a sand onto a barge.the sand leaves the dredger pipe at 4ft/s with a weight flux of 850 lbs/s. estimate the tension on the mooring line caused by this loading.

  Calculate the rocket power

rocket boosts the speed of a spacecraft from 7500 m/s to 10 500 m/s with a thrust of 890 kN. Calculate the rocket power.

  Draw the shear and moment diagrams for the beam

the traveling crane consists of a 5-m-long beam having a uniform mass per unit length of 20kg/m. The chain hoist and its supported load exert a force of 8 kN on the beam when x=2m. draw the shear and moment diagrams for the beam.

  What is the inner tube surface temperature at the outlet

What is the inner tube surface temperature at the outlet, where fully developed conditions may be assumed?

  Find the total heat loss per m length of the steam line

find the total heat loss per m length of the steam line. Find also the temperature at the interface of steam and insulation.

  Compute these two sets of centerline and control limits

Calculate these two sets of centerline and control limits. Once points are plotted, how will the results of these two charts differ?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd