What is the probability that the n-s runway is going to be

Assignment Help Civil Engineering
Reference no: EM13555180

An airport has two runways, one is North-South (N-S), and the other is East-West (E-W). Because of the prevailing winds, the E-W runway is used 80% of the days, and the N-S the remainder of the time. The selection of the runway for a given day is based on wind at the beginning of the day, and once selected will not be changed for the entire day. The airport has a single peak period each day; this is the hour between 4:00 and 5:00pm. During this peak hour, the volume of air traffic varies day to day and may be described with the normal variate N(100,10). The N-S runway is considered overcrowded of more than 125 planes use it during this period, whereas the E-W runway is considered overcrowded if more than 100 planes use it during a peak period.

a. What is the probability that the N-S runway is going to be overcrowded on a given day, if at the beginning of the day the runway is selected to be used?

b. What would be the probability of overcrowding, if at the beginning of a given day the E-W runway were selected to be used?

c. What is the probability of overcrowding at the airport, if there is no advance information as to which runway will be used on a given day?

Reference no: EM13555180

Questions Cloud

Determine the mean effective pressure of an ideal otto cycle : Determine the mean effective pressure of an ideal Otto cycle that uses air as the working fluid. At the beginning of compression the pressure is 14 psi and the temperature if 60°F.
What would be the magnitude of the mahor principal stress : A normally consolidated clay soil has angle of friction = 20 degrees and effective stress angle of friction = 28 degrees. If a consolidated undrained test is conducted on this clay
Determine the true coefficient of discharge in the equation : A rectangular channel carries a discharge of 2.00 m3/sec per meter of channel width over a weir crest that is 1.4 m in height. The energy grade line upstream of the weir measure 2.7 m above the channel bottom
Estimate the number of accidents per year in the intersect : Suppose the annual traffic flow in one of these one-way streets is 100,000 vehicles and 5% of them would encounter the amber signal light. Estimate the number of accidents per year in the intersection that would be traced back to vehicles running thr..
What is the probability that the n-s runway is going to be : What is the probability that the N-S runway is going to be overcrowded on a given day, if at the beginning of the day the runway is selected to be used?
Find the elastic modulus of the material used to construct : Given a type of material used in a wire with diameter (d = 0.25 in) that stretches 2.3 inches while 80 feet of length is under tensile load of 1800 pounds. Find the elastic modulus of the material used to construct the wire.
What air pressure in psig is needed to raise the maximum : Assume the lubricating fluid is changed to oil with a dynamic viscosity of 1.4X10E-3 lbf-s/ft^2. Now what air pressure, in psig, is required to overcome shear force ? Use the same lift rate of 0.1 ft/sec.
What is the probability that there will be at least one hot : Weather records for a certain region indicate that there is a tendency for two hot summers to occur in a row. From the statistics for the region, the following information has been es tahlished
Derive a formula for the steady rate of descent : This problem involves a cylinder falling inside a pipe that is filled with oil. The small space between the cylinder and the pipe is lubricated with an oil film that has viscosity ?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the moment of inertia and natural frequency of pipe

Find the moment of inertia and natural frequency of a vertical cantilever pipe 12 feet tall with outer diameter of 4.5 inches and an inner diameter of 4.25 inches. Modulus of Elasticity = 10*10^6 Mass = 50 lbs.

  How many moles of aluminum

How many moles of aluminum do 5.2×1024 aluminum atoms represent?

  What are the normal stresses in the bars afterward

The cross sectional area of each bar is A = 400 mm2 and L = 250 mm. If the cross bar is loaded with a load P = 250 kN, what are the normal stresses in the bars afterward?

  V is the shear force at the same point

Follow the derivation of the following equations for deflections of a beam, filling in all the required assumptions and steps in the derivations.EIv'' = M EIv''' =V EIv'''' = ? q where v is the deflection of the beam, E is Young's modulus

  What percentage of the water evaporates

Saturated liquid water at 1.0 MPa is throttled adiabatically to a pressure of 0.4 MPa. If the change is kinetic energy is negligible, what percentage of the water evaporates during this throttling process?

  Explain where the water is coming from for several decades

The Jordan aquifer has been pumped for several decades, yet remains fully saturated. Explain where the water is coming from.

  Calculate the numerical value of the leverett j- function

The medium contains a wetting phase in equal proportions. Calculate the numerical value of the Leverett J- function for this idealized porous medium. Assume the wall thickness of the capillary tube to be negligible small.

  Determine the velocity of the box 2 seconds later

A 20 kg box is on an upward inclined surface of 30 degrees from the floor. the velocity of the box is zero when it is subjected to a constant horizontal force F=30N. assuming the surface is smooth,

  What was students associated perception per reaction time

An engineering student is driving on a level roadway and sees a construction sign 500 ft ahead in the middle of the roadway. the student strikes the sign at a speed of 25 mi/h.

  When will the queue clear

where u(t) is in vehicles per minute and t is in minutes. When will the queue clear?

  Find what is the maximum you would pay for the bond

A 10-year $2000 Bond with a coupon rate of 10% paid semi-annually is available for purchase. What is the maximum you would pay for this bond if your MARR (without inflation) is 6%, and you estimate an inflation rate of 3% annually

  Determine the average shearing stress in the bolts

A composite beam is made by attaching the timber and steel portions with bolts of 14-mm diameter spaced logitudinally every 200 mm. The modulous of elasticity is 10 GPa for the wood and 180 GPa for the steel.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd