What is the pressure that the pump can deliver the

Assignment Help Mechanical Engineering
Reference no: EM13633571

A 4 kW motor is driving an oil pump with an efficiency of 95% down a 10 mm diameter pipe. If the velocities of the fluid down the pipe is 1.8 m/s

a) What is the flow rate that the pump delivers?

b) What is the pressure that the pump can deliver?

The viscosity of the oil is v = 0.00001 m2/s. Is the flow in the pipe laminar or turbulent?

Reference no: EM13633571

Questions Cloud

A uniform electric field of magnitude 380 nc pointing in : a uniform electric field of magnitude 380 nc pointing in the positive x-direction acts on an electron which is
What are the sound pressure levels at a distance of 300 500 : a suppose the sound pressure level at a distance of 100 m from a single wind turbine is 55 db. what is the sound power
Discuss the requirements of a linear programming lp model : discuss the requirements of a linear programming lp model. provide an example of an lp model and define each variable
The nucleus of 8be which consists of 4 protons and 4 : the nucleus of 8be which consists of 4 protons and 4 neutrons is very unstable and spontaneously breaks into two alpha
What is the pressure that the pump can deliver the : a 4 kw motor is driving an oil pump with an efficiency of 95 down a 10 mm diameter pipe. if the velocities of the fluid
A rubber ducky falls from a bridge that is y417 m above : a rubber ducky falls from a bridge that is y41.7 m above the river that passes beneath it. the ducky lands in a model
Light traveling in air is incident on the surface of a : light traveling in air is incident on the surface of a block of plastic at an angle of 72.7deg to the normal and is
A torque t is applied to a thin-walled tube of a cross : a torque t is applied to a thin-walled tube of a cross section in the form of a regular hexagon of a constant wall
A golfer hits her tee-shot due north towards the fairway : a golfer hits her tee-shot due north towards the fairway. her shot has an initial velocity of 60 ms. a 15 ms wind is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the carnot efficiency for this additional cycle

a nuclear power plant produces 1.2 gw of electric power at a system efficiency of 20. the plant rejects heat into a

  A steel pipe of 12-in outer diamer is fabricated from

a steel pipe of 12-in outer diamer is fabricated from 14-in-thick plate by welding along a helix that forms an angle of

  Heat amp mass transfer incropera 6th ed prob 568 asphalt

heat amp mass transfer incropera 6th ed prob. 5.68 asphalt pavement may achieve temperatures as high as 50 degree

  A pump steadily draws water through a pipe from a reservoir

a pump steadily draws water through a pipe from a reservoir at a volumetric flow rate of 22 gallons per minute. at the

  Consider a 1000-w iron whose base plate is made of

consider a 1000-w iron whose base plate is made of 0.5-cm-thick aluminium alloy 2024-t6 p2771 kgm3 and cp 875 jkg c.

  Determine the stress in the wires

a 1.5 ton crate is hoisted by three steel wires. each wire is 1/4 in. in diameter and each carries one-third of the load. determine the stress in the wires.

  1-kg of air at 200 kpa and 127 deg c is contained in a

1-kg of air at 200 kpa and 127 deg c is contained in a piston-cylinder device. air is now allowed to expand in a

  The process and volume relation is given p8-4vbar for a non

the process and volume relation is given p8-4vbar for a non flow process where v is in cubic meter.if 130kj of work is

  An acher shoots an arrow vertically upward if the arrow

an acher shoots an arrow vertically upward. if the arrow ascends to a maximum height of 100 feeta find the value of

  What is the angular acceleration of the disk for this value

when a disk rolls on a surface without slip the velocity of the point of contact of the disk with the surface is zero

  Calculate the ratio of the original and etched crack tip

the fracture strength of glass may be increased by etching away a thin surface e layer. it is believed that the etching

  Initially the pressure and volume of the gas is 200 kpa and

a gas behaves such that the product of its pressure and volume is constant pvc. initially the pressure and volume of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd