What is the pressure drop per unit length along the tube

Assignment Help Civil Engineering
Reference no: EM13534515

It is known that the velocity distribution for steady, laminar flowin circular tubes (either horizontal od vertical) isparabolic. Consider a 10 -mm- diameter horizontal tubethrough with ethyl alcohol is flowing with a steady mean velocity.15 m/s.

a. Would you expect the velocity distribution to be parabolic inthis case? Explain.

b. What is the pressure drop per unit length along the tube?

Hint: The flow will be laminar if the Reynolds number Re=ρvd/μ, remains below about 2100.

 

V= Δρh^2/12μl

Reference no: EM13534515

Questions Cloud

Relationship between speed and safety in geometric design : A light spring of a constant k=90.0 N/m is attached vertically to atable. A 2.00g balloon is filled with helium (density 0.180 kg/m^3)to a volume of 5.00m^3 and is then connected to the spring, causingit to stretch. Determine the extension distance L..
What will the concentration of megachlor be in four years : Magachlor is present in a lake having a volume of 20,000,000m3 that is used for drinking water. This waterbody can be considered well mixed. Megachlor can beconsidered a conservitive pollutant.
How do you read the moody chart : The P.C. of a 3 degree curve, whose degree is based on a chord of100 ft. arc, is at Sta. 19+39.60 and the P.T is at Sta. 25+64.60. Calculate the deflection angle from the tangent at the P.C to each100-foot station on the curve and to the P.T.
Find the dimensions of the beam : A rectangular beam, simply supported over a span of 4m, is carryinga uniform distributed load of 5kN/m and a concentrated load of 5kNat the center of the beam.
What is the pressure drop per unit length along the tube : It is known that the velocity distribution for steady, laminar flowin circular tubes (either horizontal od vertical) isparabolic. Consider a 10 -mm- diameter horizontal tubethrough with ethyl alcohol is flowing with a steady mean velocity.15 m/s.
What is the maximum annual equivalent amount : An electronic device is available that will reduce year'slabor cost by $10,000. the equipment is expected to last for eightyears. If labor is cost increase at an average rate of 7% per yearand the interest rate is 12% per year
Determine the adequacy of the design using basic principles : For the eccentric shear loading of the accompanying figure, 7/8 inch diameter A325 bolts are used in two vertical lines in a bearing-type (A325-X) connection. The loading is 10 kips dead load and 30 kips live load.
Fundamentals of hydraulic engineering : A stabilization pond is designed for a 35-day detention time. If the pond is maintained at a capacity of 40 acre-feet, what is theaverage gpd flow to the stabilizaiton pond?
Going from west to east on the same section of the road : A section of highway is 18 km long. A bus going fromeast to west on this road climbs for 6 minutes at one speed, levelsoff for 6 minutes at a second speed and descends for 6 minutes at athird speed. Going from west to east on the same section ofthe r..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What biodegradation reaction rate coefficient be achieved

Assuming the lagoons are well mixed and that there are no losses or gains of water in the lagoon other than the sewage input, what biodegradation reaction rate coefficient (in day^-1) must be achieved for a first order reaction that governs the de..

  Determine groundwater flow per unit width of the aquifer

The piezometer A is located 4,000 ft south of piezometer B.  Approximately 3,000 ft of piezometer B there is a river with an elevation relative to sea level of about 455 ft.

  Calculate the initial head loss through a dual-media filter

The porosity of both media is 0.40, the shape factor for the anthracite is 7.5, and the shape factor for the sand is 6.0. Assume a water temperature of 60 F.

  What is the ratio of night to day accidents for fatalities

What would the B/C ratio be if the light poles were twice as far apart as assumed above?

  At what load would you expect the specimen to fracture

Three-point bending test was performed on an aluminum oxide specimen having a circular cross section of radius 5.5 mm; the specimen fractured at a load of 850 N when the distance between the support points was 50 mm.

  What is the modulus of elasticity at the beginning and end

One cubic meter of nitrogen at40oC and 340 kPa iscompressed isoentropically to 0.2 m3. Calculate the finalpressure and temperature when the nitrogen is reduced to that volume.

  Determine the force exerted by the rider on the seat

determine the force exerted by the rider on the seat, the upward normal forces at A and B, and the lateral friction forces at A and B. Even though the bicycle is free to roll, assume that it does not. The bicycle weighs 29 lb with center of gravit..

  How to label turing points numerically starting with tp1

A differential leveling loop started and closed on BM Juno, elevation 5194.02 ft. The BS and FS distancces were kept approximately equal. Readings (in ft) listed in the order takken are 9.65, 2.11, 2.51, 8.35, 2.06, 9.25, 7.93, 2.83, 5.05, and 4.6..

  Determine the exit velocity of the gas mixture

Oxygen and methane are mixed at 250kPa absolute pressure and 100 degrees C. The velocity of the gases into the mixer us 5m/s. The density of the gas leaving the mixer is 2.2 kg/m^3. Determine the exit velocity of the gas mixture.

  Design condition inflow and pumping rates

Derive an equation that allows you to compute the diameter of the drain hole for a desired steady water height in the tank for the design condition inflow and pumping rates.

  Determine the volume of water infiltrated on the field

a 30-acre field received 4 inches of rain with 35% runoff.Determine the volume of water infiltrated on the field ( assume all the water that doesn't runoff infiltrates )

  Determine what is the void ratio of the soil

A natural deposit of soild was found to have water content of 20% and to be 90% saturated. What is the void ratio of the soil

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd