What is the predicted drag on the prototype dish

Assignment Help Mechanical Engineering
Reference no: EM131279803

The drag on a 2-m-diameter satellite dish due to an 80- km/hr wind is to be determined through a wind tunnel test using a geometrically similar 0.4-m-diameter model dish. Assume standard air for both model and prototype.

(a) At what air speed should the model test be run?

(b) With all similarity conditions satisfied, the measured drag on the model was determined to be 170 N. What is the predicted drag on the prototype dish?

Reference no: EM131279803

Questions Cloud

Find the range of air velocities that would be required : Determine the range of air velocities that would be required for the wind tunnel if Reynolds number similarity is desired. Are the velocities suitable? Explain.
Five consecutive nonduplicate acks : Show the values of cwnd, sstresh, and the state of the station before and after each of following events: five consecutive nonduplicate ACKs arrived followed by a time-out, and followed by two nonduplicate ACKs.
What is contribution of each bond to total portfolio risk : What is the correlation between the two bonds' returns?-  What is the contribution of each bond to total portfolio risk?
Research articles on organizations that successfully : Use the Internet or the Strayer Library to research articles on organizations that successfully go global and adopt global information systems. Next, select one (1) organization that successfully went global and adopted global information systems.
What is the predicted drag on the prototype dish : The drag on a 2-m-diameter satellite dish due to an 80- km/hr wind is to be determined through a wind tunnel test using a geometrically similar 0.4-m-diameter model dish.
How the portfolio manager use treasury bond futures contract : If the target duration for a portfolio is greater than the current portfolio duration, how can the portfolio manager use:- Treasury bond futures contracts to alter the portfolio's duration so as to bring it in line with the target duration?
How are they applied to general accounting : Can you describe GAAP guidelines? How are they applied to general accounting? Swayne, L. E., Duncan, W. J., &Ginter, P. M. (2013). Strategic management of health care organizations (7th ed.). Hoboken, NJ: Wiley.
Write a memorandum of the given case : write a memorandum outlining the issues of this case, including the crimes that the defendants (both Helen and Allen) can reasonably be charged with.
Sequential and additive composition adaptors : Explain how the sequential and additive composition adaptors differ in terms of their usage, their software integration, and their reuse.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd