What is the permanent set of the bar

Assignment Help Mechanical Engineering
Reference no: EM131170919

A round bar having a length of 2 m and a diameter of 10 mm is made of an aluminum alloy for which the stressstrain diagram can be described mathematically by the following equation:

1170_8d907932-f910-4a40-9422-6bface34290b.png

in which σ has units of megapascals (MPa). The shape of this stress-strain diagram is shown in the figure. The bar is axially loaded by tensile forces P = 20 kN, after which the loads are removed. What is the permanent set of the bar?

Reference no: EM131170919

Questions Cloud

Violence goodness and justice in american culture : "considering hate: violence, goodness and justice in american culture and politics".- Write about the quote at the start of the chapter.
Examine five issues that the it department is likely to face : Create an architectural diagram that shows how the virtual teams would collaborate and access common repositories for documents, software, development, and testing facilities. Use Visio or an equivalent such as Dia. Note: The graphically depicted ..
What are some issues that concern for-profit organizations : Public Relations Key Issues and Concerns Research the following types of organizations "Nonprofit, For-profit, Political and Government and International", identify key concerns for each and provide each type of organization. What are some issues tha..
Does organization encourage positive organizational behavior : Write a 500- to 700-word analysis of the team's chosen organization and its climate regarding organizational behavior. Include the following in your review: Does this organization encourage positive Organizational Behavior
What is the permanent set of the bar : The shape of this stress-strain diagram is shown in the figure. The bar is axially loaded by tensile forces P = 20 kN, after which the loads are removed. What is the permanent set of the bar?
What reforms are needed to improve effectiveness of texas : Write an essay discussing what reforms are needed to improve the effectiveness of the Texas governor and allow him to be an effective leader of the executive branch and an effective leader of the state.
What is the modulus of elasticity e : What is the modulus of elasticity E of the highstrength material used for a 3 mm diameter wire if the wire stretches 29 mm when a 12 m length of it is subjected to a tensile load of 4 kN?
Who should get revenue from naming rights : How should stadium / arena revenues be distributed? Who will you sell naming rights to? Why? Who should get revenue from naming rights? How long and for how much
Write a ten page paper on statesmanship : Write a 7-10-page paper on statesmanship not including the title page and the reference page. Note: the paper must contain an introduction and a conclusion.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd