What is the percentage of energy lost during the impact

Assignment Help Mechanical Engineering
Reference no: EM131113033

Problem 1 - A particle of mass m slides down a frictionless chute and enters a circular loop of diameter d. Find the minimum starting height h in order that the particle will make a complete circuit of the loop and exit normally without having lost contact with the loop.

2102_Figure.png

Problem 2 - A skier descends the smooth slope above (right) starting from rest at point A. Her total mass is 52 kg. Determine the normal force she exerts on the ground the instant she arrives at B. What is her acceleration at this point?

Problem 3 - The block shown below is released from rest. What is the maximum velocity of the block, the maximum compression of the spring and the maximum distance from the spring after it rebounds up the plane?

292_Figure3.png

Problem 4 - At the instant shown above (right) block B is 30 m below the level of Block A. At this time the velocity of each block is zero. Determine the velocities of A and B as they pass each other. The mass of A is 15 kg and the mass of B is 5 kg. The pulleys are light.

Problem 5 - A 10-kg block swings down and strikes an identical block. Assume that the 6-m rope breaks during impact and the coefficient of restitution is zero. How long will it be before m2 comes to rest? How far will it have traveled? What is the percentage of energy lost during the Impact? Compare the results to the case where e = 1.

1655_Figure5.png

Problem 6 - A cannonball is fired as shown above (right) with an initial speed of 1600 ft/sec. The cannon recoils and strikes a plate attached to a spring. Find the maximum spring deflection if the plane is smooth and the spring constant is 500 lb/ft.

Problem 7 - Weight W1 falls from rest through a distance H; it lands on another weight W2, which was in equilibrium atop a spring of modulus k. If the coefficient of restitution is zero, find the maximum compression of the spring.

827_Figure7.png

Problem 8 - Two identical hockey pucks collide, coming into contact in the positions shown above (center). Their velocities before collision are given above. If e = 0.8, find the velocities of the pucks after collision and the impulse of the force on puck B.

Problem 9 - A man of mass m and a boat of mass M are at rest as shown above (right). If the man walks to the front of the boat, what is his distance from the pier at that instant?

Reference no: EM131113033

Questions Cloud

Calculate the risk premium on its common stock : Given the following information for the stock of Foster Company, calculate the risk premium on its common stock. Current price per share of common ........ $50.00 Expected dividend per share next year ...... $ 3.00
Prepare the journal entry for wood incorporated and engram : Wood Incorporated factored $150,000 of accounts receivable with Engram Factors Inc. on a without-recourse basis.
Distributed throughout the population : You need to hire some new employees to staff your start-up venture. You know that potential employees are distributed throughout the population as follows, but can't distinguish among them:
What moral guide should american society use : While it is easier to defend a middle-ground position that either strict moral absolutism or moral relativism, nonetheless, it is possible to create a good argument for any position along the spectrum between absolutism and relativism.
What is the percentage of energy lost during the impact : A 10-kg block swings down and strikes an identical block. Assume that the 6-m rope breaks during impact and the coefficient of restitution is zero. How long will it be before m2 comes to rest? How far will it have traveled? What is the percentage o..
What is the exponential rate of rainforest destruction : What is the exponential rate of rainforest destruction in units of 1/days?
Is accepting a free meal ethical as a police officer : What are the pros and cons in accepting the free meal? What are the pros and cons in not accepting the free meal? Do you think that police officers should be held to a "higher standard" than people in other professions?
Prepare the october 1 journal entries for chung or seneca : On October 1, 2010, Chung, Inc. assigns $1,000,000 of its accounts receivable to Seneca National Bank as collateral for a $750,000 note.
Allocating public health resources : Imagine that you are standing on the bank of a river and injured people start floating down the river towards you. There is no end to the floating people...they just keep coming and coming. You are alone and you do not have cell service to phone f..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd