What is the percentage error in the accelerometer

Assignment Help Civil Engineering
Reference no: EM132782220

An accelerometer is measuring a structure as described below: Damping ratio of accelerometer = 0.65 Highest frequency measured by the accelerometer = 6000 hz

Natural frequency of the accelerometer = 18000 hz

What is the percentage error in the accelerometer at the highest frequency it can measure?

Reference no: EM132782220

Questions Cloud

Draw the structure of graphite schematically : Draw the structure of Graphite schematically. Describe the type of chemical bonds in the structure. Explain how "graphene" is fabricated from graphite.
What would the gst amount be : If inventory was purchased for $2 288 inclusive of GST, what would the GST amount be? Which items decreases the balance in the accounts receivable?
Establish and maintain a cooperative social order : Social contract theorists say that morality consists of a set of rules governing how people should treat one another that rational beings will agree to accept.
Describe the applied loads and forces : Describe the applied loads and forces acting on the Spar (of an aeroplane) including any environmental effects i.e. stress regimes
What is the percentage error in the accelerometer : What is the percentage error in the accelerometer at the highest frequency it can measure?
What the effect on income would be a : Assume Talent Industries could avoid $80,000 of fixed manufacturing overhead if it purchases the component, What the effect on income would be a?
What strain is measured at the elevated temperature : A strain gauge is used at a temperature far above where it is calibrated.
What factors most contributed to the anti slavery arguments : In your opinion, what factors most contributed to the "pro" and "anti"-slavery arguments and why? What factors do you believe most influenced one's respective.
Find the entropy change in kj-k : Ninety kilograms of ice at 0 deg. celsius completely melted. Find the entropy change in KJ/K? (Take latent heat of ice as 320 KJ/Kg)

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what should the velocity for the model be

The prototype and model will both be in air, if the prototype has a velocity of 500 ft/s and a diameter of 30 ft, what should the velocity for the model be if the model diameter is 2 ft

  What engineering parameter must the joint surfaces possess

A slope face is cut in granite with sheet joints dipping as shown. A) Disregarding information about cohesion or friction along the joint surfaces, state why the cut is stable

  Determine the linear interpolation function of displacement

Consider a 2D triangular element with the three vertices at 1[1,1], 2[1,2] and 3[2,2]. the displacements at these t hree points are [0.1,0.1], [0.3,0.2] and [0.4, 0.3] mm for point 1,2,and 3 respectively

  Determine the normal stresses induced in portions ab

A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E=29x10^6 psi, α=6.5x10^-6) and portion BC is made of aluminum (E=6.5x10^-6 psi, α=13.3x10^-6).

  What is the diameter of a circular concrete column needed

What is the diameter of a circular concrete column needed to support a load of 300,000 pounds with a factor of safety of 2? Round the diameter up to the whole inch. The concrete ultimate strength is 3000 lb/in^2.

  Compute the radius of the new curve

The highway engineer of a certain road construction decided to use a radius of 100 m. in laying out a simple curve having an angle of intersection

  Two crews are to start at opposite ends of a mountain

A standard five-day BOD test is run using a mix consisting of fourparts distilled water and one part wastewater (no seed). Theinitial DO of the mix is 9.0 mg/L, and the DO after five days isdetermined to be 1.0 mg/L. What is BOD5 ?

  Determine the low-level codes and the gross

There is a scheduled receipt of 100 Cs in week 2. Quantities required of each are also shown.

  Describe why materials such as aluminum-steel and basswood

1. Describe why materials such as aluminum, steel, basswood, and Polystyrene Plastic and structures are important in our everyday lives. 2.Write a paragraph to explain to a lay person a few of the important factors

  Calculate the magnitude of the total force supported

The uniform 4 meter boom has a mass of 60 kg and is pivoted to the back of the truck at A and secured by a cable at C. Calculate the magnitude of the total force supported by the connection at A

  Why do owners prefer the design-build form of contracts

Why do owners prefer the design-build form of contracts when many of them know they can obtain better quality construction using other forms. What are the stages at which the designer will schedule design reviews.

  Calculate the equilib-rium constant at 25°c for the reaction

If there is no water vapor in the air, the oxygen partial pressure would have been 0.2. Assuming that nitrogen, oxygen, and water vapor are the only important contributors to the gas pressure, calculate the equilib-rium constant at 25°C for the re..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd