What is the percent increase in the air velocity

Assignment Help Mechanical Engineering
Reference no: EM13212863

A hair dryer is a constant diameter duct containing an electrical resistor. A small fan pushes air through the duct past the resistor and the air is heated when electrical current flows through the resistor. If the room temperature is 15C and the temperature of the air exiting the hair dryer is 50C, what is the percent increase in the air velocity as it passes through the dryer.

Reference no: EM13212863

Questions Cloud

Explain macrs and double declining balance method : A piece of equipment used for research is purchased for $870,000 and is to be depreciated over a specific period of time. If the salvage value at the end of its depreciable life is $50,000, show the yearly depreciation using a) Straight line metho..
Find the instant centers of all three bars : Two collars C and D move along the vertical rod as shown. Knowing that the velocity of collar C is 50 in/s downward, find the instant centers of all three bars, the angular velocity of AB, the velocity of collard D.
Define equilibrium constant for the elctrochemical reaction : The equilibrium constant for the elctrochemical reaction 2Fe+Cu3(PO4)2 = 2FePO4 + 3Cu occuring in aqueous solution
What is the allowable minimum length of the ramp : If the ramp height is 2ft. Using the ada code, what is the allowable minimum length of the ramp?
What is the percent increase in the air velocity : If the room temperature is 15C and the temperature of the air exiting the hair dryer is 50C, what is the percent increase in the air velocity as it passes through the dryer.
Draw conclusions concerning the process : Draw conclusions concerning the process, and relate your interpretation to the possible existence of chance and assignable causes of variation.
How much work was done on the roof by the forces : In 1975 the roof of Montreal's Velodrome, with a weight of 360 kN, was lifted by 10 cm so that it could be centered. How much work was done on the roof by the forces making the lift?
How much will you need to put down in order to buy the hous : You are going to purchase a house which costs $250,000. Your annual income is currently $60,000. The bank you are going to get the mortgage from uses a 28% qualifying rate (a maximum of 28% of your gross monthly income can go to your monthly payme..
Explain reactions spontaneous and non-spontaneous : Are the following reactions spontaneous, non-spontaneous, or not possible?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd