What is the peak discharge at the reach outlet

Assignment Help Civil Engineering
Reference no: EM13552751

Use the Muskingum method to route a flood through a reach a river. The base flow is 100 cfs, and the incoming flood flow increases 50 cfs every 2 hr over a 6 hr period and the subsides at the same rate. From past observations the time lag between peaks at the inlet and outlet of the reach is 2.5 hr, and the x coefficient is 0.35. What is the peak discharge at the reach outlet, and when does it occur?

Reference no: EM13552751

Questions Cloud

Calculate the absolute pressure at an ocean depth : Calculate the absolute pressure at an ocean depth of 75 m. Assume the density of sea water is 1 028 kg/m3 and the air above exerts a pressure of 101.3 kPa
Determine the probability that the annual runoff from : The total annual runoff from small drainage basin is determined to be approximately normal with a mean of 14.0 in. and a variance of 9.0in^2. Determine the probability that the annual runoff from the basin will be less than 11.0 in. in all three of t..
What is the period of the second harmonic? : One of the mooring lines of USS BOXER (LHD-4) is under a tension of 4500 N and is set into resonance by the vibration of a CHT pump. What is the period of the 2nd harmonic
What percentage change in the tension of the wire : The G string of a guitar which should be 392 Hz is playing flat at 380 Hz. What percentage change in the tension of the wire is required so as to tune the string to 392 Hz
What is the peak discharge at the reach outlet : Use the Muskingum method to route a flood through a reach a river. The base flow is 100 cfs, and the incoming flood flow increases 50 cfs every 2 hr over a 6 hr period and the subsides at the same rate.
Determine the change in storage during : Athletic Lake has a surface area of 75.96 km2. In September, the evaporation was estimated to be 3.20 inches and the precipitation was 3.45 inches. The average flow rate of the River Tiger into the lake was determined to be 3.5 m3/s and the average f..
Find the magnitude of the magnets magnetic dipole moment : A bar magnet is oriented with its magnetic dipole moment at 53.5° to the direction of a 0.0629-T magnetic field, Find the magnitude of the magnet\'s magnetic dipole moment
Estimate the separation distance of the wires : Two long parallel wires carry currents of 2.83 A and 5.41 A. Find the separation distance of the wires expressed in millimeters
Calculate the mass flux rate and the flow rate : Water is flowing in a 6-cm diameter pipe at 20 m/s at 10?C. If the pipe enlarges to a diameter of 12-cm, calculate the reduced velocity. Also, calculate the mass flux rate and the flow rate.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the force across the whole beam from the left end

A beam with a total length of 14m, has a 1000N load on the left end, 4m to the right (from the left end of the beam) there is a rolarr, 2m to the right of the rolar begins a 300 N/m load that goes for 4m, and the last 4m has a tapered load of 300 ..

  What will the volume of the sample be at the water content

A saturated 100 cm^3 clay sample has a natural water content of30%. It's found that the shrinkage limit occurs when the water content is 19%. If the specific gravity of soil solids is 2.7,

  Calculate the area of reinforcement required

A short Reinforced Concrete column is 300mm x 400mm. It is required to carry an ultimate load of 1500kN and an ultimate major axis bending moment of 300kNm. Calculate the area of reinforcement required.

  Calculate the r-value for the wall assembly

Calculate the R-value for the wall assembly. This calculation should be done by hand, on engineering paper, and handed in during class (or scanned and submitted online).

  Is the noise level of area 1 greater than 60 decibels

Office workers complain that the noise level in their office Area 1 is greater than that in the company's other office Area 2. Six measurements are made on different days in each area, with the following results

  Determine the maximum allowable uniform load what

A W410 X 0.83 steel section is used in a10 m simple span. Determine the maximum allowable uniform load what the beam can carry if the allowable flexural stress is 165MPa, the allowable shear stress is 100 MPa, and the allowable deflection is 1/360 of..

  Calculate the discharge through the flume

A long throated flume is built in a rectangular 1 m widechannel having a throat width of 0.5m. The upstream head is 0.6 m.Assume a Cd of 1.0.

  What is the area of longitudinal steel required for column

A short concrete column is being used to support the roof over a pedestrian walkway. The unbraced column length is 9 feet and supports a dead load of 12 kips and a live load of 20kips.

  How does the result differ from the case of oblique impact

In the Civil War there were numerous incidents in which the bullet fired from a Union soldier's rifle struck and fused with the bullet from a Confederate's rifle. Assume the impact scenario.

  Estimate the pressure 200m downstream of the treatment plant

water from a treatment plant is pumped into distribution system at a rate of 4.38 m^3/sec, a pressure of 480 kpa and a temperature of 20 degree celcius. The pipe has a diameter of 750 mm and is made of ductile iron

  Estimate the undrained shear strength of clay

Plot variation with depth from the top to Point C for σ' v and σ h when the soil is at rest and Estimate the undrained shear strength (c u ) of clay. (Assume the shear strengths to be 200 kPa and 2 kPa at Liquidity Index (IL) values of 0 and 1, res..

  What is the effective theoretical detention time

Determine the surface area of a primary settling tank sized to be handle a maximum hourly flow of 0.570 m3/s at an overflow rate of 60 m/day.If the effective tank depth is 3.0 m,what is the effective theoretical detention time?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd