What is the particular solution for capacitance current

Assignment Help Electrical Engineering
Reference no: EM13226743

In a series RC circuit, R = 5 Ohms and C = 0.1F. The capacitor voltage is 10 volts at t=0. At t=0, a voltage of 4V is applied.

a) Determine the total capacitance voltage and capacitance current as a function time after the external voltage is applied.

b) Accurately plot capacitance voltage and current

c) What is the particular solution for capacitance current if the input voltage is 3tu(t)?

Reference no: EM13226743

Questions Cloud

Find out the maximum number of equivalent resonance : Draw out the Lewis structures for H2CO3, HCO3-, and CO32-. Then determine the maximum number of equivalent resonance structures for each species. Note that carbon is the central atom in all three cases
What is the value of the capacitor : An inductive circuit of 50 ohm resistance and 0.08H inductor are connected in series with a capacitor across a 200-V 50-Hz supply. The current is 3.8A leading. What is the value of the capacitor
. identify each system as either undamped or overdamped : The following 4 differential equations describe mass spring systems. Identify each system as either undamped, overdamped, underdamped, or critically damped (Justify your answer). Determine the angular frequency and period for the undamped
Explain the stepwise formation constants for zn : Given the stepwise formation constants for Zn(NH3)4 complex are logKf1=2.18 , logKf2=4.43 , logKf3=6.74 , logKf4=8.70 and the pKb fo ammonia is 4.76.
What is the particular solution for capacitance current : In a series RC circuit, R = 5 Ohms and C = 0.1F. The capacitor voltage is 10 volts at t=0. At t=0, a voltage of 4V is applied. a) Determine the total capacitance voltage and capacitance current as a function time after the external voltage is applied..
Compute the volume of o2 obtained : Hydrogen peroxide undergoes a first-order decomposition to water and O2 in aqueous solution. The rate constant at 25 °C is 7.40 * 10-4 s-1. Calculate the volume of O2 obtained from the decomposition of 1.00 mol H2O2 at 25 °C and 740 mmHg after 20...
Determine the electric and potential in dielectric region : The upper and lower conducting plates of a large parallel-plate capacitor are separated by a distanced and maintained at potentials V0 and 0, respectively. A dielectric slab of dielectric constant 6.0
Explain the graduated cyinder far from the magnet : 296K(temperature), if you placed 2.58g of CrCl3*6H2O in a graduated cylinder and attempted the same experiment, what ?m would ypu observe?
Calculate the electrostatic energy that is stored : Calculate the electrostatic energy that is stored in the structure if the intermediate space is filled with a dielectric whose relative dielectric constant is 10 and a voltage is applied between the conductors creating an electric field.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the electrostatic energy that is stored

Calculate the electrostatic energy that is stored in the structure if the intermediate space is filled with a dielectric whose relative dielectric constant is 10 and a voltage is applied between the conductors creating an electric field.

  Find the aliased frequency of the signal

Determine the location of the peaks in the following sampled spectrum for the following sine waves: (a.) signal frequency = 300 Hz; sampling frequency = 1 kHz (b.) signal frequency = 600 Hz ; sampling frequency = 1 kHz

  Which real wage rate is higher

In 1988, the average wage rate was $9.45 an hour and in 2008 the average wage rate was $18.00 an hour. The CPI in 1988 was 118.3 and in 2008 it was 215.3 . Which real wage rate is higher?

  Finding appropriate source for the electrical load

Finding appropriate source for the electrical load, Have four circuits. One takes 9Vdc, two 5Vdc, and last one takes 12Vdc. Have variable transformer for source. How do I calculate or choose the voltage needed to run all four circuits with out blo..

  How the reverse movement of the motor be controlled

Design I/O wiring to control forward and reverse 12Vdc motor using PLC OMRON CJ1M. Consider that the forward movement of the motor will be controlled by a forward button and the reverse movement of the motor will be controlled by a reverse button

  Calculate the resistors resistance

calculate the resistor's resistance. If the bandwidth were cut to 25 kHz, determine the expected output meter reading.

  What is the fundamental benefit of plc controls

1.Calculate motor speed in revolutions per minute for an eight-pole,50Hz motor. Give the equation and identify its parts; show your math. 2.You need to detect finished products coming down an assembly line.

  Design a collision free circuit for a router

A network router connects multiple computers together and allows them to send messages to each other. If two or more computers send messages simultaniously, they collide and the messages must be resent. Design a collision free circuit for a router..

  How small would a number have to be indistinguishable from 0

Assume that we will use a double-precision number for non-integer numbers (if you recall, this means a binary "scientific notation" with a sign bit, 11 exponent bits using an excess-1024 representation, and a 53-bit mantissa of the form 1.--52 bits-..

  What are the design implications for the location

Now that you have gained some familiarity with solar cells and their characteristics, what are your impressions about the efficiencies of these devices What are some applications for solar cells that are currently being used Why is this technology..

  How parameters must be constrained to make system constant

In the question below only focus on the parameter or parameters that are relevant to the particular property you are being asked about in the particular question. If you need to constrain a parameter to satisfy the stated criterion.

  What is the per unit value if we change the base

A generator is rated at 500 MVA (three phase) and 22 kV (line-to-line). Its Y-connected windings have a reactance of 1.1 per unit. Find the ohmic value of the reactance of the windings. What is the per unit value if we change the base to 200 MVA a..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd